Product Overview
The RY high-temperature molten salt pump is a single-stage, single-suction, cantilever-type vertical sump pump. Developed from the manufacturer's experience producing high-temperature sump pumps and informed by comparable overseas designs, it is intended for molten-salt circulation systems and transfer duties.
The pump is designed for high-temperature molten salt service up to 600°C. A typical medium is a nitrate mixture containing 53% KNO₃, 40% NaNO₂ and 7% NaNO₃. Applications include chlor-alkali production using ion-exchange membranes and alumina processing, as well as other high-temperature liquid duties.
Model designation example: 100RY-37B
100: Flow rate (m³/h)
R: High-temperature service
Y: Vertical pump
37: Head (m)
B: Material code
The RY series is described as a dedicated pump for high-temperature molten salt circulation and transfer. The manufacturer states that domestically produced molten salt pumps now have approximately 95% locally manufactured components, with annual production capacity exceeding 4,000 units.
Product Features
1. High-efficiency hydraulic design
The pump uses a centrifugal impeller and is intended for low-flow, high-head service. Its hydraulic design is stated to provide good efficiency, although efficiency is slightly lower than that of the GY molten salt pump.
2. Reliable, stable operation
The pump is designed for smooth operation with low vibration and noise, long service life, fewer repairs and lower maintenance costs. The manufacturer describes its quality as comparable to that of similar overseas products.
3. Stable support above the liquid
The motor support, bearing frame and mounting baseplate are all above the liquid level. This arrangement provides stable support for the pump and helps maintain smooth operation.
4. Dual cooling for high-temperature service
The bearing housing has a cooling jacket to reduce the temperature of the lubricant and bearings. A second cooling jacket in the bearing seat below the housing helps prevent heat from the submerged section from conducting upward.
This dual-cooling arrangement is intended to support operation in high-temperature service. With appropriate cooling, construction and materials, the pump is described as suitable for nitrate molten salt below 540°C; some manufacturers state a maximum operating temperature of 600°C.
5. Cantilever design with no submerged mechanical seal
The cantilever arrangement places the bearing system above the liquid. There is no sealing arrangement in the submerged section, eliminating the associated leakage points. The shaft is supported by a combination of rolling and sliding bearings and is connected to the motor by a flexible coupling. The source states that this design reduces operating vibration by more than 30%.
6. Single-pipe, symmetrical flow passage
The pump uses a single-pipe, symmetrical flow-passage design, intended to reduce radial forces. The source claims this can increase equipment life by 40% and improve head efficiency by 15%. The casing is a cylindrical, double-wall structure that integrates the inlet and discharge functions and has a removable end cover to facilitate maintenance.
7. Stable bearing arrangement
The bearing frame and bearing assembly are oil-lubricated and fitted with water-cooling jackets. Cooling water can be circulated through the jackets.
The submerged sliding bearing can be made from the same or a higher-grade material than the main shaft, or from special impregnated graphite or silicon carbide (SiC). Rolling-bearing grease lubrication and self-lubricating bearing liners are used to support long-term operation and help prevent external contaminants from entering the bearing assembly.
The submerged shaft, shaft sleeve, bearing liner and pump casing operate at a similar temperature, reducing the risk of seizure caused by differential thermal expansion.
8. Materials for high-temperature and corrosive service
Flow-passage components may use martensitic or austenitic stainless steel, including 304 and 316; duplex stainless steel such as 2205; or high-temperature alloys such as Inconel 625.
Key components may receive surface nitriding treatment to improve corrosion resistance.
The manufacturer specifies precision casting with casting tolerances of ±0.2 mm and a flow-passage surface roughness of Ra ≤3.2 μm.
A stated heat-treatment process consists of solution treatment at 1,050°C followed by aging at 590°C, with a target hardness of HRC 28–32.
Materials and cooling arrangements are intended to minimize thermal-expansion problems and reduce the risk of the shaft sleeve or bearing seizing at high temperatures.
9. Multistage, high-head options
A multistage configuration, such as the RYB type, can be designed to provide higher heads and a wider selection range for high-power, high-head duties.
10. Product development
The GY high-temperature molten salt sump pump is described as an upgraded successor developed from the manufacturer's RY series, incorporating design features from comparable overseas products and intended to offer improved performance.
Applications
The RY pump is intended for circulating or transferring high-temperature molten salts, including nitrate and nitrite salts. Listed applications include:
- Chemical industry: Molten-salt heating and circulation systems in ion-exchange-membrane chlor-alkali plants; process duties in the production of anthraquinone, lubricants, phthalic anhydride, maleic anhydride, pyromellitic dianhydride, acrylic acid, fumaric acid and melamine; and inorganic chemical processes such as alumina and soda ash production.
- Concentrated solar power: High-temperature salt circulation between collectors, storage tanks and heat exchangers.
- Thermal energy storage: Long-distance transfer and circulation of hot media in molten-salt energy-storage systems.
- Metallurgy: Circulation of high-temperature media in aluminum, magnesium and metal heat-treatment processes.
- Power generation: High-temperature heat-transfer-fluid circulation in thermal power plants.
- Building materials and plastics: Transfer of heating media used in rubber, plastics and building-materials production.
- Nuclear and advanced materials research: The source also lists molten-salt reactor cooling duties and transfer or control of liquid metals and other specialized high-temperature media.
- Other applications: Circulation of high-temperature heat-transfer fluids in environmental-treatment systems and other specialized high-temperature processes.
Technical Specifications
1. Design Standards
Design, manufacture and inspection are stated to follow ISO 5199 and relevant standards, including GB/T 13008 for mixed-flow and axial-flow pumps. Rotor components are specified with a dynamic-balance grade of G6.3 and radial runout of ≤0.05 mm.
2. Construction
The RY is a single-stage, single-suction, cantilever-type vertical sump pump. The source describes it as a horizontal-motor/vertical-pump arrangement, directly driven through a claw-type flexible coupling. Viewed from the motor end, the specified direction of rotation is clockwise.
Main components include the pump casing, pump cover, impeller, shaft, connecting pipe, discharge pipe, bearing housing, motor frame, bearing seat, baseplate or mounting flange, coupling and motor. The section below the pump baseplate is installed inside the molten-salt tank.
3. Operating Principle
Pumping:
A motor drives the main shaft through a flexible coupling. The centrifugal impeller submerged in the molten salt rotates at high speed, drawing salt from the bottom of the tank and discharging it upward through the discharge pipe. The casing, impeller and pump cover are submerged during operation. The submerged design does not require a shaft seal to contain the pumped liquid.
Bearing lubrication:
The submerged guide bearing is lubricated and cooled by the molten salt itself, so no separate external lubricating-liquid system is required.
4. Cooling System
- Bearing cooling: Two rolling bearings are installed in the bearing housing and are lubricated and cooled by circulating light oil. The oil circulates through the bearing arrangement and returns to the oil chamber. The bearing housing has a water-cooling jacket.
- Thermal-barrier cooling: The bearing seat below the bearing housing also has a cooling jacket for water. This helps limit heat conduction from the submerged section to the bearing housing.
The dual-cooling system is intended to keep the bearing assembly within its operating-temperature range when conveying molten salt at 540–600°C, subject to the specific pump design and operating conditions.
5. Drive and Direction of Rotation
The motor drives the pump shaft directly through a claw-type flexible coupling. Viewed from the motor end, the pump rotates clockwise.
6. Wetted-Part Materials
- Pump casing and cover: Austenitic stainless steel such as 304 or 316; alloy steel such as QT500-7; martensitic stainless steel such as ZG15Cr13; high-temperature alloy such as Inconel 625; or duplex stainless steel such as 2205.
- Impeller: Austenitic stainless steel such as 304 or 316, martensitic stainless steel, high-temperature alloy or nitrided cast steel.
- Main shaft: Precipitation-hardening stainless steel such as 17-4PH, duplex stainless steel or high-temperature alloy.
- Guide bearing / shaft sleeve: Special impregnated graphite, SiC or high-temperature wear-resistant material compatible with the main shaft.
- Bearing seat / frame: Cast steel or alloy steel, with a water-cooling jacket.
- Connecting bolts: 35CrMoA or precipitation-hardening stainless steel.
The source specifies precision casting and a heat-treatment schedule of solution treatment at 1,050°C for 2 hours followed by water quenching, then aging at 590°C for 8 hours followed by air cooling. The stated target hardness is HRC 28–32, with flow-passage roughness of Ra ≤3.2 μm.
7. Operating Conditions
- Flow rate (Q): 3–600 m³/h for the RY series; up to 3,700 m³/h for the RY(L) series. Larger sizes may be available to order.
- Head (H): 10–80 m for the RY series; up to 400 m for the RY(L) series. Some models are stated to exceed 120 m.
- Speed (n): 1,450–2,980 r/min, depending on model.
- Operating pressure: ≤1.2 MPa; some models up to 2.5 MPa, depending on casing material and temperature.
- Medium temperature: −20°C to +600°C, with the upper limit depending on material grade.
- Submergence depth: 1–6 m, customizable. Some RY(L) models can be installed at depths of up to 20 m.
8. Sealing Arrangement
The cantilever design has no dynamic or static seal in the submerged section, eliminating those potential leakage paths for toxic, hazardous, flammable or explosive media. The above-liquid section uses an open bearing-seat arrangement with a water-cooling jacket. The motor's explosion-protection rating can be selected according to user requirements.
9. Installation Requirements
Lower the pump assembly into the molten-salt tank and connect the baseplate flange to the tank-top flange. Provide adequate ventilation and heat dissipation. Support the discharge piping independently so that the discharge flange is not subjected to additional external loads.
Connect bearing-cooling-water lines in parallel and fit flow indicators to monitor cooling-water supply during operation. Before startup, check that the direction of rotation matches the arrow on the pump and confirm that the submerged section is fully immersed in the molten salt.
10. Operating Precautions
Before startup, confirm that the molten salt is fully melted and has reached the required pumping temperature, generally above 180°C. No solidified salt should remain inside the pump.
Start the cooling-water supply before starting the pump. After shutdown, continue cooling until the pump temperature has fallen to ambient temperature before shutting off the cooling water, to prevent bearing overheating.
For a prolonged shutdown, drain the molten salt from the pump. Electric heat tracing may be used to melt and drain residual salt, preventing solidification from blocking the pump or piping.
For other corrosive, toxic or specialized media, provide the medium's name, temperature, concentration, density and viscosity when ordering so that suitable materials and safety measures can be specified.
Structural Drawings

Performance Data Tables
|
Model |
Flow rate (m³/h) |
Head (m) |
Speed (r/min) |
Motor power (kW, reference) |
Motor model (reference) |
|
20RY-20 |
20 |
20 |
1450 |
7.5 |
Y132M-4 |
|
20RY-30 |
20 |
30 |
1450 |
11 |
Y160M-4 |
|
35RY-20 |
35 |
20 |
1450 |
7.5 |
Y132M-4 |
|
45RY-30 |
45 |
30 |
1450 |
15 |
Y160L-4 |
|
65RY-20 |
65 |
20 |
1450 |
15 |
Y160L-4 |
|
70RY-30 |
70 |
30 |
1450 |
22 |
Y180L-4 |
|
120RY-20 |
120 |
20 |
1450 |
18.5 |
Y180M-4 |
|
120RY-30 |
120 |
30 |
1450 |
30 |
Y200L-4 |
|
200RY-20 |
200 |
20 |
1450 |
30 |
Y200L-4 |
|
200RY-30 |
200 |
30 |
1450 |
55 |
Y250M-4 |
|
120RY-55 |
120 |
55 |
1450 |
55 |
Y250M-4 |
|
150RY-23 |
150 |
23 |
2980 |
18.5 |
Y160L-2 |
|
150RY-30 |
150 |
30 |
2980 |
22 |
Y180M-2 |
|
300RY-20 |
300 |
20 |
1450 |
45 |
Y225M-4 |
|
300RY-30 |
300 |
30 |
1450 |
75 |
Y280S-4 |
|
300RY-72 |
300 |
72 |
1450 |
200 |
Y315M-4 |
|
450RY-72 |
450 |
72 |
1450 |
280 |
Y355L-4 |
|
300RYB-72 |
300 |
72 |
1450 |
200 |
Y315M-4 |
|
400RYB-72 |
400 |
72 |
1450 |
250 |
Y355M-4 |
|
650RYB-72 |
650 |
72 |
1450 |
400 |
Y400-4 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: ry molten salt vertical sump pump, China ry molten salt vertical sump pump manufacturers, factory


