FYU-J Agitated Fluoropolymer Sump Pump

FYU-J Agitated Fluoropolymer Sump Pump

The FYU-J Agitated Fluoropolymer Sump Pump is an extended version of the FYU series of corrosion- and abrasion-resistant sump pumps. It is designed for media that are prone to clogging or settling. An agitator at the lower end of the pump helps keep solids suspended while the pump conveys the slurry, reducing the risk of blockage at the suction inlet.
The FYU-J can handle slurries containing solids and is also suitable for removing and conveying settled material from sumps, settling tanks and other vessels.
Send Inquiry
Description

Product Overview

 

The FYU-J Agitated Fluoropolymer Sump Pump is an extended version of the FYU series of corrosion- and abrasion-resistant sump pumps. It is designed for media that are prone to clogging or settling. An agitator at the lower end of the pump helps keep solids suspended while the pump conveys the slurry, reducing the risk of blockage at the suction inlet.

The FYU-J can handle slurries containing solids and is also suitable for removing and conveying settled material from sumps, settling tanks and other vessels.

The FYU series is an upgraded replacement for the YU sump pump. It is a fully plastic pump made from modified UHMWPE, offering improved wear and corrosion resistance compared with the earlier YU polymer sump pump. With more than ten years of manufacturing history, the series has been continuously refined through performance improvements and the development of application-specific models. It now includes four product families and a broad range of models, with maximum flow rates of up to 600 m³/h. The manufacturer reports stable performance and operating quality, and a repeat-customer rate of 95%.

Model designation example (based on the FYU series naming convention):

FY: Corrosion-resistant sump pump

U: Plastic construction (UHMWPE)

J: Equipped with an agitator

The following numbers indicate the inlet diameter (mm), head (m) and submergence depth (mm), respectively.

 

Product Features

 

1. Agitator helps prevent settling and clogging

The pump shaft extends below the impeller and suction inlet, with an agitator fitted at its lower end. As the shaft rotates, the agitator cuts through and disturbs the surrounding medium, suspending settled solids so they can be drawn into the impeller and discharged.

This helps prevent solids from settling in particle-laden liquids and can also loosen existing sediment deposits. By combining agitation and pumping in one unit, the design can eliminate the need for separate mixing equipment and reduce related investment and operating costs.

2. Excellent corrosion and wear resistance

The wetted components are formed as an integral molding from UHMWPE engineering plastic. Among engineering plastics, UHMWPE offers outstanding wear and impact resistance, strong resistance to creep and good corrosion resistance. It is suitable for acidic and alkaline slurries and clean liquids at temperatures from −20°C to 90°C.

All submerged parts are designed for corrosion resistance. The pump operates without external leakage and is designed for reliable service at an economical cost.

3. No shaft-seal leakage

The vertical long-shaft design places the impeller, pump casing and other wetted components partially below the liquid surface, keeping the shaft-seal area out of contact with the liquid. This eliminates leakage risks associated with conventional mechanical or packing seals, making the pump suitable for corrosive, toxic or volatile media and applications with special safety requirements.

4. Large-pitch threaded connections for corrosion protection

The pump casing is integrally molded, and the connecting tube is made of fiberglass-reinforced plastic. This combines corrosion resistance with structural strength.

Large-pitch threaded connections join the pump casing to the connecting tube and to the pump cover. No metal fastening screws are used in the submerged section, reducing the risk of corrosion-related damage and supporting long-term corrosion protection.

5. Smooth operation and low maintenance

Rolling bearings in the above-liquid section and submerged sliding guide bearings support the pump's axial and radial loads, helping ensure smooth, quiet operation. The guide bearings are lubricated by the pumped medium, so no external lubrication system is normally required. External lubrication can be provided for special operating conditions.

6. Simple installation and compact footprint

The pump is installed vertically and mounted directly on the vessel through its baseplate, requiring no additional floor space. Installation typically involves securing the pump vertically in position and connecting the discharge line. Removal and maintenance are also straightforward.

7. Broad model range with long-term field use

The series offers nearly 200 models, with maximum flow rates of up to 600 m³/h. The manufacturer reports that the products have been used over the long term by more than 300 customers at over 1,000 operating locations. Users have recognized their temperature capability, corrosion and wear resistance, mechanical stability and economical operating costs. The series is positioned as an alternative to metal pumps.

8. Custom material options

For applications with specific corrosion-resistance requirements, the pump casing, impeller and other components can be made from alternative materials, including F2/F46 fluoropolymer alloys and polypropylene (PP), to suit the pumped medium.

 

Applications

 

The FYU-J Agitated Fluoropolymer Sump Pump is suitable for lifting and conveying corrosive or non-corrosive clean liquids and slurries from low-level tanks. It is particularly effective in applications involving suspended solids or media that readily settle.

Typical applications include:

  • Non-ferrous metal hydrometallurgy: Transfer of acids, alkalis, corrosive ore slurries, electrolytes, waste acids and wastewater in the hydrometallurgical production of lead, zinc, gold, silver, copper, manganese, cobalt, rare earths and other metals.
  • Phosphate fertilizer and acid production: Transfer of dilute acids, mother liquors, fluorosilicic acid containing silica gel, phosphoric acid slurries and similar media.
  • Water treatment and environmental protection: Transfer of contaminated industrial wastewater and settling-tank sludge. Typical duties include sump pumping, wastewater pumping, waste-liquid transfer and extraction-liquor transfer.
  • Agrochemical, dye and fine chemical industries: Transfer of acids and alkalis containing solvents, mixed acids, and solvent-bearing slurries, including acidic and alkaline slurries.
  • Other industries: Transfer of corrosive or non-corrosive clean liquids and slurries in the chemical, petroleum, machinery, metallurgical, pharmaceutical, food, electroplating, power generation and pulp and paper industries.

 

Suitable media and operating conditions

  • Slurry solids concentration by weight: Less than 20%
  • Maximum solid-particle diameter: Less than 0.5 mm
  • Medium temperature: Below 90°C

Under equivalent media and operating conditions, the pump can be used as an alternative to higher-cost special stainless-steel and fluoropolymer sump pumps.

 

Technical Specifications

 

1. Design Principle and Construction

The FYU-J Agitated Fluoropolymer Sump Pump is based on the FYU sump pump, with the shaft extended beyond the impeller and below the suction inlet. An agitator is fitted at the shaft end. During operation, the agitator rotates with the pump shaft, continuously disturbing the surrounding medium and suspending settled solids. The impeller draws in the resulting slurry and discharges it upward through the discharge pipe, allowing the pump to agitate and convey at the same time.

The pump is a vertical, single-stage, single-suction centrifugal pump with a long-shaft design. The pump casing, intermediate connecting pipe, bearing support, discharge pipe and pipe flanges are bolted together as an assembly and secured to a baseplate. The complete pump is mounted on the vessel through the baseplate. The suction inlet is axial, drawing liquid from beneath the impeller; the discharge outlet is parallel to the pump axis and directs liquid upward.

 

2. Wetted-Part Materials and Manufacturing

The wetted components are integrally molded from high-performance ultra-high-molecular-weight polyethylene (UHMWPE) engineering plastic. UHMWPE offers excellent wear, impact and creep resistance, together with good corrosion resistance. The pump casing is integrally molded, while the connecting tube is made of fiberglass-reinforced plastic, combining corrosion resistance with structural strength.

For special requirements, the pump casing, impeller and other wetted components can be made from:

F2/F46 fluoropolymer alloy: Offers higher temperature resistance and is suitable for highly corrosive media.

Polypropylene (PP): An economical option for general corrosive service.

 

3. Shaft-Seal Arrangement and Bearing System

The FYU-J uses a vertical long-shaft submerged design. The pump casing, impeller and other wetted components are immersed in the liquid, while the bearings, coupling and other drive components remain above the liquid surface in the atmosphere. There is no rotary seal where the shaft passes through the liquid surface, avoiding the leakage risks associated with conventional mechanical seals or packing seals.

Axial and radial loads-including hydraulic forces generated during operation and the weight of the impeller and rotor-are carried by a one-way thrust ball bearing, a single-row radial ball bearing and sliding guide bearings in the bearing housing. The rolling bearings are grease-lubricated.

A submerged water-lubricated bearing (sliding guide bearing) is fitted at the lower part of the pump. Pumps with a submergence depth greater than 1 m are equipped with an intermediate submerged bearing, which is lubricated by the pumped medium to support stable, reliable operation. If the medium contains normal, small amounts of particles, clean external liquid can also be supplied to lubricate the guide bearings.

 

4. Operating Conditions

  • Flow rate (Q): 2–400 m³/h; maximum capacity may reach 600 m³/h
  • Head (H): 5–50 m; some models reach 80 m
  • Speed (n): 1,450 or 2,900 r/min, depending on the model
  • Suitable temperature: −20°C to 90°C for UHMWPE; up to 150°C with F46 material
  • Submergence depth (L): 250–2,500 mm; custom depths available
  • Slurry concentration: Less than 20% by weight
  • Maximum solid-particle diameter: Less than 0.5 mm
  • Motor power: 1.5–75 kW, selected according to medium density and operating conditions
  • Inlet diameter: 25–150 mm
  • Outlet diameter: 20–125 mm

 

5. Installation and Operating Precautions

a. Installation check:

Secure the pump vertically in the required position and connect the discharge pipe. After installation, turn the coupling by hand to confirm that it rotates freely. If it binds or makes abnormal noise, disassemble the pump and check for debris or other problems. Maintain a clearance of 1–2 mm between the impeller and pump casing, and 1–2 mm between the impeller and pump cover. Adjust by adding or removing shims. Test repeatedly until the pump turns freely before connecting the power supply.

b. Start-up:

Briefly energize the motor to check that its direction of rotation matches the arrow on the pump. If the directions do not match, correct the wiring. Once the motor is confirmed to run normally, open the discharge valve gradually to reach the required operating condition. The pump casing must be submerged at start-up, with the liquid level above the impeller centerline. Do not operate the pump if the liquid level is below the impeller.

c. Shutdown:

Close the discharge valve first, then switch off the power.

d. Explosion-proof configuration:

The pump can be configured for hazardous or non-hazardous areas. For use in a hazardous area, an explosion-proof motor can be specified.

e. Special media:

When pumping special media, provide the medium's name, temperature, concentration, density, viscosity, solids content and particle size so the manufacturer can select suitable materials and configuration.

 

Structural Drawings

 

product-1270-847

Performance Data Tables

 

Model

Inlet × outlet (mm)

Flow rate (m³/h)

Flow range (m³/h)

Head (m)

Head range (m)

Motor power, SG < 1.2 (kW)

Motor power, SG 1.2–1.4 (kW)

Submergence depth (mm)

25FYU-J-12

25×20

5

2~7

12

15~5

1.1

1.5

500/750/1000/1250/1500/1750/2000/2250/2500

25FYU-J-15

25×20

5

2~7

15

20~5

1.5

2.2

500/1000/1500

32FYU-J-15

32×25

10(8)

5~15(5~13)

15

20~5

3.0(2.2)

4.0(3)

500/1000/1500

40FYU-J-20

40×32

10

8~15

20

25~10

3

4

500/1000/1500

40FYU-J-30

40×32

10

8~15

30

35~15

3

4

500/1000/1500

50FYU-J-30

50×40

20

10~30

30

32~15

5.5(4)

7.5(5.5)

500/1000/1500

65FYU-J-50

65×65(65×50)

30

20~70

50

60~28

15

18.5

500/1000/1500

80FYU-J-35

80×65

40

25~70

35

36~16

11

15

500/1000/1500

100FYU-J-38

100×80

60

30~100

38

41~20

18.5

22

500/1000/1500

100FYU-J-40

100×80

100

50~130

40

42~24

30

30

500/1000/1500

150FYU-J-40

150×125

150

100~250

40

42~23

45

55

500/1000/1500

150FYU-J-26

150×125

220

150~300

26

35~10

30

37

500/1000/1500

If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.

Hot Tags: fyu-j agitated fluoropolymer sump pump, China fyu-j agitated fluoropolymer sump pump manufacturers, factory

Send Inquiry