Product Overview
The LJYA Cantilever Slurry Sump Pump is a vertical, single-stage, single-suction centrifugal pump with a cantilever shaft. Developed with reference to advanced products from China and abroad, it is designed to convey abrasive and corrosive media containing up to 30% solids and with a viscosity below 200 cP. It is particularly suitable for phosphoric acid and ammonium phosphate slurries in the phosphate fertilizer industry.
The submerged section of the shaft has sufficient rigidity. No bearing is fitted between the impeller and pump casing, allowing the pump to handle media with relatively high solids concentrations. It is a suitable alternative to conventional long-shaft sump pumps for slurry service.
Model designation example: 50LJYA-25A
50: Pump inlet diameter (mm)
LJYA: Vertical cantilever pump designation: L, vertical; J, cantilever; Y, sump; A, slurry
25: Rated head (m)
A: Impeller-trim sequence designation
Product Features
Cantilever construction with no submerged bearings
No bearing is installed in the submerged section. The impeller is cantilever-mounted at the lower end of the pump shaft. This eliminates common issues associated with submerged bearings in conventional long-shaft pumps, such as wear, lubrication requirements and vulnerability during dry running. The pump can handle media with relatively high solids concentrations and tolerate short periods of dry running without damage to the pump casing.
Semi-open impeller and replaceable wear plates
The impeller is semi-open and fitted with replaceable wear components at both the front and rear. The front cover has a wear-plate design, while the rear cover incorporates an upper wear plate. These components help protect the pump from erosion by solid-laden slurries.
Because the wear plates are separate replaceable parts, they can be changed as they wear, avoiding replacement of the complete casing or impeller and reducing spares and maintenance costs.
Shaft-seal-free design
The pump operates with its casing submerged in the medium and does not require a mechanical seal or packing seal. This removes the shaft-seal leakage points found in conventional pump designs, making it suitable for corrosive, toxic or safety-sensitive media.
Broad range of corrosion-resistant materials
Depending on the pumped medium, wetted components can be made from 1Cr18Ni9Ti, 304, 304L, 316, 316L, Cr30A, CD4MCu, and other stainless steels or corrosion-resistant alloys, including J-1 alloy and 20Cb3.
The manufacturer also offers CD4-2, a duplex stainless steel developed for corrosion and abrasion resistance. It is reported to have been used in demanding service with low maintenance frequency and long service life.
Reliable construction and stable operation
The main components include the front cover with wear plate, pump casing, impeller, rear cover with wear-resistant construction, connecting pipe, baseplate, bearing assembly, motor support, coupling and discharge-pipe assembly. The design is intended to provide low vibration and noise, with stable and reliable operation.
Broad performance range
The stated flow range is 5–400 m³/h, and the stated head range is 5–80 m. The submerged depth is 0.6–1.5 m, with a cantilever length of 1–1.8 m from the baseplate to the impeller centerline.
Applications
The LJYA is suitable for abrasive and corrosive liquids containing solid particles, with viscosity below 200 cP as specified for abrasive service. Typical applications include:
Phosphate fertilizer production: Transfer of phosphoric acid, ammonium phosphate slurry and other media with combined abrasive and corrosive properties. Typical duties include phosphoric acid extraction and ammonium phosphate concentration.
Compound fertilizer and fertilizer production: Transfer of ammonium nitrate, urea and solid-bearing slurries.
Chemical industry: Transfer of acids, alkalis, salt solutions and reaction slurries containing solids.
Non-ferrous metallurgy and hydrometallurgy: Transfer of solid-bearing acidic mineral slurries, electrolytes and pickling solutions.
Environmental protection and water treatment: Transfer of corrosive wastewater containing solids and circulation of limestone slurry in flue-gas desulfurization systems.
Technical Specifications
1. Design Standards
The pump is designed and manufactured in accordance with applicable enterprise and industry specifications. Some models reference GB/T 5656 and relevant API standards to meet general centrifugal-pump requirements for chemical and metallurgical process service.
2. Construction
The LJYA is a vertical, single-stage, single-suction cantilever centrifugal pump. It has a semi-open impeller fitted with replaceable wear plates at the front and rear. There are no bearings in the submerged section; the cantilever shaft is designed with sufficient rigidity for submerged operation.
3. Operating Principle
The motor drives the pump shaft through a flexible coupling. As the submerged impeller rotates at high speed, centrifugal force draws liquid into the impeller eye and discharges it upward through the pump casing and discharge pipe. Because the pump casing is submerged, the pump can start without priming.
4. Drive and Direction of Rotation
The pump is driven by an electric motor through a flexible coupling. Viewed from the motor end, the pump rotates clockwise.
5. Wetted-Part Materials
- 1Cr18Ni9Ti (321): Common option for general corrosive and abrasive service.
- 304/304L: For moderately corrosive service; 304L offers improved resistance to intergranular corrosion.
- 316/316L: For pitting-prone service, including some chloride-containing media.
- Cr30A: High-chromium ferritic stainless steel for highly acidic, abrasive service.
- CD4MCu / J-1 alloy: Duplex stainless-steel options for strongly corrosive, solid-bearing slurries.
- CD4-2: A newer duplex stainless steel for demanding corrosion and abrasion service.
- 20Cb3: High-nickel alloy option for sulfuric acid and other special media.
6. General Performance Range
- Flow rate (Q): 5–400 m³/h across the series
- Head (H): 5–80 m; some specifications state a maximum of 132 m
- Speed (n): 1,450 or 2,900 r/min, depending on model
- Medium temperature: 0–105°C standard. For higher-temperature service, bearing cooling with cooling water may be required.
- Suitable viscosity: Below 200 cP for abrasive service; below 300 cP for solid-bearing viscous media, depending on the medium and configuration
- Solids concentration: Up to 30%; some applications are stated to reach 35%
- Maximum particle diameter: Below 2 mm
- Submergence depth: 0.6–1.5 m standard
- Cantilever length: 1–1.8 m
- Inlet diameter: 25–200 mm, depending on flow-rate model
- Motor power: 0.75–90 kW, selected according to actual operating conditions
Structural Drawings

Performance Data Tables
|
Model |
Flow rate (m³/h) |
Head (m) |
Speed (r/min) |
Motor power (kW) |
|
25LJYA-5 |
1.6 |
5 |
1450 |
1.1 |
|
25LJYA-8 |
1.6 |
8 |
1450 |
1.5 |
|
25LJYA-12.5 |
1.6 |
12.5 |
1450 |
2.2 |
|
25LJYA-20 |
1.6 |
20 |
1450 |
2.2 |
|
40LJYA-5 |
3.2 |
5 |
1450 |
1.5 |
|
40LJYA-8 |
3.2 |
8 |
1450 |
1.5 |
|
40LJYA-12.5 |
3.2 |
12.5 |
1450 |
2.2 |
|
40LJYA-20 |
3.2 |
20 |
1450 |
3 |
|
50LJYA-5 |
6.3 |
5 |
1450 |
1.5 |
|
50LJYA-8 |
6.3 |
8 |
1450 |
2.2 |
|
50LJYA-12.5 |
6.3 |
12.5 |
1450 |
2.2 |
|
50LJYA-20 |
6.3 |
20 |
1450 |
3 |
|
65LJYA-5 |
12.5 |
5 |
1450 |
1.5 |
|
65LJYA-8 |
12.5 |
8 |
1450 |
2.2 |
|
65LJYA-12.5 |
12.5 |
12.5 |
1450 |
3 |
|
65LJYA-20 |
12.5 |
20 |
1450 |
4 |
|
65LJYA-32 |
12.5 |
32 |
1450 |
7.5 |
|
80LJYA-5 |
25 |
5 |
1450 |
2.2 |
|
80LJYA-8 |
25 |
8 |
1450 |
3 |
|
80LJYA-12.5 |
25 |
12.5 |
1450 |
4 |
|
80LJYA-20 |
25 |
20 |
1450 |
5.5 |
|
80LJYA-32 |
25 |
32 |
1450 |
11 |
|
80LJYA-50 |
25 |
50 |
1450 |
18.5 |
|
100LJYA-5 |
50 |
5 |
1450 |
3 |
|
100LJYA-8 |
50 |
8 |
1450 |
4 |
|
100LJYA-12.5 |
50 |
12.5 |
1450 |
5.5 |
|
100LJYA-20 |
50 |
20 |
1450 |
7.5 |
|
100LJYA-32 |
50 |
32 |
1450 |
15 |
|
100LJYA-50 |
50 |
50 |
1450 |
30 |
|
125LJYA-12.5 |
100 |
12.5 |
1450 |
11 |
|
125LJYA-20 |
100 |
20 |
1450 |
15 |
|
125LJYA-32 |
100 |
32 |
1450 |
22 |
|
125LJYA-50 |
100 |
50 |
1450 |
37 |
|
150LJYA-20 |
200 |
20 |
1450 |
22 |
|
150LJYA-32 |
200 |
32 |
1450 |
37 |
|
10LJYA30-4 |
10 |
30 |
1450 |
7.5 |
|
10LJYA40-2 |
10 |
40 |
2900 |
7.5 |
|
15LJYA30-4 |
15 |
30 |
1450 |
7.5 |
|
20LJYA25-4 |
20 |
25 |
1450 |
7.5 |
|
20LJYA30-4 |
20 |
30 |
1450 |
11 |
|
20LJYA55-4 |
20 |
55 |
1450 |
15 |
|
25LJYA20-4 |
25 |
20 |
1450 |
7.5 |
|
27LJYA20-4 |
27 |
20 |
1450 |
7.5 |
|
30LJYA30-4 |
30 |
30 |
1450 |
11 |
|
45LJYA20-4 |
45 |
20 |
1450 |
15 |
|
45LJYA35-4 |
45 |
35 |
1450 |
15 |
|
54LJYA20-4 |
54 |
20 |
1450 |
15 |
|
60LJYA20-4 |
60 |
20 |
1450 |
15 |
|
100LJYA50-4 |
100 |
50 |
1450 |
30 |
|
160LJYA30-4 |
160 |
30 |
1450 |
37 |
|
200LJYA35-4 |
200 |
35 |
1450 |
45 |
|
200LJYA50-4 |
200 |
50 |
1450 |
55 |
|
400LJYA30-4 |
400 |
30 |
1450 |
55 |
|
400LJYA50-4 |
400 |
50 |
1450 |
90 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: ljya cantilever slurry sump pump, China ljya cantilever slurry sump pump manufacturers, factory


