Product Overview
The IJ pump is a single-stage, single-suction, overhung chemical process pump developed as a successful product of China's Seventh Five-Year Plan science and technology program. Incorporating technical features from API 610 and ASME B73.1-2001, it is an upgraded design based on the IH pump.
The IJ is a horizontal, single-stage, single-suction, overhung pump with axial suction and radial discharge. Its performance parameters comply with GB/T 5662 (equivalent to ISO 2858), and its design also references ISO 5199 for centrifugal-pump technical requirements and API 682 for mechanical-seal piping plans.
Following more than a decade of development and range expansion, the series includes over 100 sizes. It is intended to cover a broad range of chemical-process duties at pressures up to 2.5 MPa and temperatures up to 200°C. Alongside the CZ and ZA series, it is one of the widely used chemical process pump ranges in China.
Compared with the IH pump, the IJ has an optimized hydraulic design and a reinforced shaft arrangement. The source states that its efficiency is approximately 5% higher. A larger shaft diameter and shorter overhang are intended to reduce shaft failures, improve operating stability and lower maintenance and operating costs.
Product Features
1. High efficiency and optimized hydraulics
The pump uses an optimized hydraulic design, with efficiency stated to be approximately 5% higher than that of a conventional IH pump. CFD analysis is used to refine the flow passages. Smooth wetted surfaces help reduce hydraulic losses and support favorable cavitation performance.
2. Reinforced construction for reliable operation
The shaft diameter is increased and the impeller overhang is reduced, drawing on ANSI pump design practices. These changes are intended to address shaft failures commonly associated with IH pumps.
The asymmetric-section volute and casing without wear rings are designed to improve suitability for some solids-bearing duties. The pump is intended to operate with low vibration and noise.
3. Back-pull-out design for easier maintenance
The pump is foot-mounted. The pump cover is located on the bearing bracket and clamped between the bracket and casing. For maintenance, the drive assembly can be withdrawn from the casing after removing the connecting nuts; the suction and discharge piping can remain in place.
On larger models, a spacer section between the pump and motor couplings allows the drive assembly to be removed without moving the motor. This is a commonly used arrangement for chemical process pumps.
4. Multiple sealing options for demanding service
The mechanical seal and seal chamber have been developed with reference to API 682. The 171-series mechanical seal is used in applications including soda ash, chlor-alkali, salt production, metallurgy, paper and environmental treatment, as well as services involving crystallization or suspended particles.
Depending on the medium, the pump can be supplied with a single or double mechanical seal, packing seal or hydrodynamic seal. Seal flushing and cooling arrangements can be selected with reference to API 610 recommendations.
5. Broad materials range
Wetted-part materials include cast iron, cast steel, 304 and 304L stainless steel, 316 and 316L stainless steel, CD-4MCu, 904 and 904L stainless steel, Hastelloy and titanium alloys. The material can be selected according to the corrosiveness of the pumped medium.
6. Solids-bearing service
The standard stated capability is for liquids containing suspended particles smaller than 3 mm, with solids content below 5%. Some extended-range models are stated to handle slurries with solids content below 50%, including liquids containing crystalline impurities. Confirm the allowable solids content and particle characteristics for the selected model.
Applications
The IJ pump is intended for corrosive or contamination-sensitive liquids, including services with small amounts of suspended solids or crystals. Typical applications include:
- Soda ash and inorganic salts: Ammonia brine and mother liquor from the ammonia-soda and combined soda processes; soda ash; diaphragm-cell and membrane-cell caustic solutions; chlorides, hypochlorites, sodium sulfide, sulfates and hydrogen peroxide.
- Non-ferrous metallurgy: Copper and nickel electrolytes, sodium aluminate solutions in alumina production, acid mist in cobalt production, zinc-process slurries, ammonium vanadate, and acid-mist or thiourea solutions in gold production.
- Iron and steel: Electroplating solutions, pickling liquids, waste-acid treatment liquids and electrophoretic coatings.
- Acid production: Hydrochloric, nitric, sulfuric, phosphoric and acetic acids, as well as phosphoric-acid slurry.
- Petrochemicals: Petroleum refining, cracking and separation processes; butadiene, alkylbenzene and methanol production.
- Synthetic fibers and plastics: Polyester, dichloromethane, epichlorohydrin, trichloropropane, PVC and dimethylformamide (DMF) processes.
- Pulp and paper: Pulp-cooking liquor, green liquor, white liquor, concentrated black liquor and bleaching liquids.
- Fertilizers: Urea, ammonium nitrate, ammonium bicarbonate, ammonium chloride, ammonium phosphate, potassium chloride and potassium sulfate.
- Fermentation and pharmaceuticals: Process intermediates, lactic acid, citric acid, food additives, beer, fermentation broths, and pharmaceutical and pesticide production.
- Environmental protection: Chemical dosing and treatment of acidic or alkaline wastewater.
Technical Specifications
Design Standards
- GB/T 5662, equivalent to ISO 2858-1975, for dimensions of end-suction centrifugal pumps
- ISO 5199 for centrifugal-pump technical requirements
- API 682 for mechanical-seal piping plans
Design references: API 610, 10th edition, and ASME B73.1-2001
Pump Configuration
API 610 OH1-type arrangement: horizontal, single-stage, single-suction, overhung pump with a foot-mounted casing.
Operating Conditions
- Maximum rated operating pressure: Up to 2.5 MPa
- Standard medium temperature: −20°C to +105°C
- Special configurations: Up to +175°C to +200°C, for example with a cooling system
- Maximum ambient temperature: 40°C
- Direction of rotation: Clockwise when viewed from the motor end toward the pump
- Standard stated solids capability: Suspended particles smaller than 3 mm and solids content below 5%; some extended models are stated to handle up to 50%
- Viscosity: Similar to water
General Performance Range
- Flow rate (Q): 0.64–2,400 m³/h across the basic series and trimmed-impeller models
- Head (H): 3.5–250 m
- Speed (n): 1,450 / 2,900 r/min; direct motor drive or variable-frequency control
- Design pressure: ≤2.5 MPa
- Medium temperature: −20°C to +200°C stated overall; normally up to 105°C, with special measures for 175–200°C service
- Inlet diameter: 50–200 mm
- Motor power: 0.55–160 kW, selected according to medium density and viscosity
- Motor protection rating: IP54 / IP55 / IP65, as specified
- Motor insulation class: F
Structural Drawings

Performance Data Tables
|
Model |
Speed (r/min) |
Flow rate Q (m³/h) |
Head H (m) |
Efficiency η (%) |
Shaft power (kW) |
Motor power (kW) |
NPSHr (m) |
Impeller diameter (mm) |
|
IJ25-25-125 |
1450 |
1.6 |
5 |
45 |
0.05 |
0.55 |
1 |
125 |
|
IJ25-25-160 |
1450 |
1.6 |
8 |
37 |
0.09 |
0.55 |
1 |
160 |
|
IJ40-32-125 |
1450 |
3.2 |
5 |
46 |
0.09 |
0.55 |
1 |
125 |
|
IJ40-32-160 |
1450 |
3.2 |
8 |
42 |
0.17 |
0.55 |
1 |
160 |
|
IJ40-32-200 |
1450 |
3.2 |
12.5 |
38 |
0.29 |
0.55 |
1 |
200 |
|
IJ50-32-125 |
1450 |
6.3 |
5 |
45 |
0.19 |
0.55 |
1 |
125 |
|
2900 |
12.5 |
20 |
51 |
1.33 |
2.2 |
1.5 |
125 |
|
|
IJ50-32-160 |
1450 |
6.3 |
8 |
40 |
0.34 |
0.55 |
1.2 |
160 |
|
2900 |
12.5 |
32 |
46 |
2.37 |
3 |
1.8 |
160 |
|
|
IJ50-32-200 |
1450 |
6.3 |
12.5 |
33 |
0.65 |
0.75 |
1.2 |
200 |
|
2900 |
12.5 |
50 |
39 |
4.36 |
5.5 |
2 |
200 |
|
|
IJ50-32-250 |
1450 |
6.3 |
20 |
27 |
1.27 |
1.5 |
1.5 |
250 |
|
2900 |
12.5 |
80 |
33 |
8.25 |
11 |
2 |
250 |
|
|
IJ65-50-125 |
1450 |
12.5 |
5 |
55 |
0.31 |
0.55 |
1.2 |
125 |
|
2900 |
25 |
20 |
62 |
2.2 |
3 |
1.8 |
125 |
|
|
IJ65-50-160 |
1450 |
12.5 |
8 |
51 |
0.53 |
0.75 |
1.4 |
160 |
|
2900 |
25 |
32 |
57 |
3.82 |
5.5 |
2 |
160 |
|
|
IJ65-40-200 |
1450 |
12.5 |
12.5 |
46 |
0.93 |
1.1 |
1.5 |
200 |
|
2900 |
25 |
50 |
52 |
6.55 |
7.5 |
2 |
200 |
|
|
IJ65-40-250 |
1450 |
12.5 |
20 |
39 |
1.75 |
2.2 |
1.5 |
250 |
|
2900 |
25 |
80 |
46 |
11.84 |
15 |
2.2 |
250 |
|
|
IJ65-40-315 |
1450 |
12.5 |
32 |
33 |
3.3 |
4 |
1.8 |
315 |
|
2900 |
25 |
125 |
39 |
21.83 |
30 |
2.5 |
315 |
|
|
IJ80-65-125 |
1450 |
25 |
5 |
64 |
0.53 |
0.75 |
1.4 |
125 |
|
2900 |
50 |
20 |
69 |
3.95 |
5.5 |
2 |
125 |
|
|
IJ80-65-160 |
1450 |
25 |
8 |
62 |
0.88 |
1.1 |
1.5 |
160 |
|
2900 |
50 |
32 |
67 |
6.5 |
7.5 |
2.2 |
160 |
|
|
IJ80-50-200 |
1450 |
25 |
12.5 |
57 |
1.49 |
2.2 |
1.5 |
200 |
|
2900 |
50 |
50 |
63 |
10.81 |
15 |
2.2 |
200 |
|
|
IJ80-50-250 |
1450 |
25 |
20 |
53 |
2.57 |
3 |
1.8 |
250 |
|
2900 |
50 |
80 |
57 |
19.11 |
22 |
2.5 |
250 |
|
|
IJ80-50-315 |
1450 |
25 |
32 |
43 |
5.07 |
7.5 |
2 |
315 |
|
2900 |
50 |
125 |
52 |
32.73 |
37 |
2.8 |
315 |
|
|
IJ100-80-125 |
1450 |
50 |
5 |
69 |
0.92 |
1.1 |
1.8 |
125 |
|
2900 |
100 |
20 |
73 |
7.46 |
11 |
2.5 |
125 |
|
|
IJ100-80-160 |
1450 |
50 |
8 |
69 |
1.58 |
2.2 |
2 |
160 |
|
2900 |
100 |
32 |
73 |
11.94 |
15 |
3 |
160 |
|
|
IJ100-65-200 |
1450 |
50 |
12.5 |
68 |
2.5 |
3 |
2 |
200 |
|
2900 |
100 |
50 |
73 |
18.65 |
22 |
3.2 |
200 |
|
|
IJ100-65-250 |
1450 |
50 |
20 |
63 |
4.32 |
5.5 |
2.2 |
250 |
|
2900 |
100 |
80 |
68 |
32.03 |
37 |
3.5 |
250 |
|
|
IJ100-65-315 |
1450 |
50 |
32 |
58 |
7.51 |
11 |
2.5 |
315 |
|
2900 |
100 |
125 |
62 |
54.88 |
75 |
3.8 |
315 |
|
|
IJ125-100-200 |
1450 |
100 |
12.5 |
73 |
4.66 |
5.5 |
2.5 |
200 |
|
2900 |
200 |
50 |
77 |
35.35 |
45 |
3.5 |
200 |
|
|
IJ125-100-250 |
1450 |
100 |
20 |
70 |
7.78 |
11 |
2.8 |
250 |
|
2900 |
200 |
80 |
72 |
60.49 |
75 |
4 |
250 |
|
|
IJ125-100-315 |
1450 |
100 |
32 |
65 |
13.4 |
18.5 |
3 |
315 |
|
2900 |
200 |
125 |
68 |
100.06 |
110 |
4.5 |
315 |
|
|
IJ125-100-400 |
1450 |
100 |
50 |
62 |
21.96 |
30 |
3.2 |
400 |
|
IJ150-125-250 |
1450 |
200 |
20 |
77 |
14.16 |
18.5 |
3 |
250 |
|
IJ150-125-315 |
1450 |
200 |
32 |
72 |
24.2 |
30 |
3.5 |
315 |
|
IJ150-125-400 |
1450 |
200 |
50 |
70 |
38.89 |
45 |
3.8 |
400 |
|
IJ200-150-250 |
1450 |
400 |
20 |
79 |
27.57 |
37 |
4 |
250 |
|
IJ200-150-315 |
1450 |
400 |
32 |
77 |
45.24 |
55 |
4.5 |
315 |
|
IJ200-150-400 |
1450 |
400 |
50 |
78 |
69.8 |
90 |
5 |
400 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: ij chemical process pump, China ij chemical process pump manufacturers, factory


