Product Overview
The CZ chemical process pump is a horizontal, single-stage, single-suction centrifugal pump with a radially split casing. Its dimensions and performance are stated to comply with DIN 24256, ISO 2858 and GB 5662-85. The series is a standardized chemical-process pump range, with a performance envelope covering that of the IH standard chemical pump series. The source states that CZ pumps exceed IH pumps in key indicators such as efficiency and cavitation performance, and can be used as direct replacements for corresponding IH models.
The pump has a back-pull-out design and an extended coupling. For maintenance, the rotating assembly can be removed without disconnecting the casing or the suction and discharge piping, reducing maintenance effort and downtime.
CZ pumps are designed for liquids that may be hot or cold, neutral or corrosive, clean or particle-laden, toxic, or flammable. Typical industries include chemicals, petrochemicals, refining, pulp and paper, sugar production and environmental treatment.
Product Features
1. Hydraulic performance
The pump has a relatively flat performance curve, making it suitable for duties with changing flow rates. The supplied specifications state an efficiency range of 17–88% and a required net positive suction head (NPSHr) range of 1.0–9.0 m. Efficiency and cavitation performance depend on the model and operating point.
2. Back-pull-out construction for easier maintenance
The casing is bolted to the bearing bracket. For maintenance, the rotor assembly-including the impeller, shaft seal and bearing housing-can be withdrawn after removing the casing-to-bracket bolts. The pump casing and connected piping can remain in place.
3. Robust mechanical design
- Casing: Integral support feet allow the casing to carry piping loads and transfer them to the foundation, helping limit rotor distortion caused by pipe loads.
- Impeller: Closed, semi-open or fully open designs are available. Axial thrust is reduced using back vanes or balance holes; the bearings carry the residual thrust.
- Bearings: The source specifies three bearings and oil lubrication. A constant-level oiler maintains the oil level.
- Radial-force reduction: Some larger models use a double-volute casing to help balance radial forces.
4. Corrosion and temperature resistance
Wetted materials can be selected for the pumped medium. The stated operating-temperature range is −80°C to +300°C, with a maximum operating pressure of 2.5 MPa, subject to the model and configuration.
5. Multiple shaft-seal options
The seal chamber is designed to accommodate different sealing arrangements according to the duty:
- Packing, with or without cooling
- Single mechanical seal
- Double mechanical seal
- Tandem mechanical seal
6. Replaceable shaft sleeve
A replaceable sleeve protects the shaft from direct contact with the pumped medium, helping reduce corrosion and extend shaft service life.
7. Stable, low-noise operation
Precision-machined rotating components and a heavy-duty bearing housing are intended to provide smooth operation with low vibration and noise.
Applications
CZ pumps are used in industrial duties requiring corrosion resistance, temperature capability and reliable operation, including:
Chemical and petrochemical industries: Inorganic acids such as sulfuric, nitric, hydrochloric and phosphoric acid; organic acids; alkaline solutions such as sodium hydroxide and sodium carbonate; and salt solutions.
Oil refineries: Liquid petroleum products, organic compounds, corrosive feedstocks and process products.
Pulp and paper: Pulp, black liquor and white liquor.
Fertilizer and agrochemical production: Corrosive process liquids and agrochemical feedstocks.
Chlor-alkali and soda ash production: Corrosive acids and alkalis.
Sugar production: Syrups and other process liquids.
Environmental treatment and water processing: Corrosive wastewater and brine in desalination plants.
Power plants: Desulfurization slurry and chemical water-treatment liquids.
Coating and surface treatment: Liquids used in degreasing, phosphating and electrophoretic coating.
Marine applications: Seawater, fresh water and chemical liquids.
Technical Specifications
1.Performance Range
- Flow rate (Q): 2–2,200 m³/h
- Head (H): 1–160 m
- Operating pressure (P): ≤2.5 MPa standard; 1.6 MPa or ANSI Class 150 options listed
- Operating temperature (T): −80°C to +300°C
- Speed (n): 1,450 / 1,480 / 2,900 / 2,960 r/min, depending on motor pole count and frequency
- Efficiency (η): 17–88%
- Required NPSH (NPSHr): 1.0–9.0 m
- Pump weight: 40–2,100 kg
These are series-level ranges. The allowable operating limits for a particular pump depend on its model, materials, seals and operating point.
2. Construction Materials
|
Component |
Standard material |
Optional materials |
|
Pump casing |
Cast iron / cast steel |
ZG1Cr18Ni9, ZG1Cr18Ni9Ti, ZG0Cr18Ni12Mo2Ti, ZG1Cr18Ni12Mo2Ti |
|
Impeller |
Cast iron / cast steel |
ZG00Cr14Ni14Si4, ZG00Cr18Ni10, CGCr28, ZG1Cr18Mn13Mo2N |
|
Shaft |
45 carbon steel |
304, 316, 316L stainless steel or duplex stainless steel |
|
Shaft sleeve |
304 stainless steel |
316L, ceramic coating or hard alloy |
|
Mechanical seal |
Silicon carbide / graphite |
Hard alloy / silicon carbide, Monel or Hastelloy |
|
Bearings |
Domestic precision bearings |
SKF, FAG or NSK |
|
Motor |
Y-series standard motor |
YB-series explosion-proof motor |
Materials such as 316, 316L and Monel may be selected for specific corrosive media. Material compatibility should be assessed against the actual chemical composition, concentration and temperature.
3. Model Designation
- Example: CZ 32-160
- CZ: Chemical process pump series
- 32: Nominal inlet and outlet diameter (mm)
- 160: Nominal impeller diameter (mm)
4. Standards and Operating Configuration
- Design and manufacturing standards stated: DIN 24256 / ISO 2858 / GB 5662-85 / API 610 (10th edition) / VDMA 24297
- Flange standards: PN16 / PN25 standard; ANSI Class 125 / 150 options listed
- Direction of rotation: Clockwise when viewed from the motor end toward the pump
- Motor protection rating: IP54 / IP55
- Insulation class: F
- Standard power supply: 380 V / 50 Hz
- Other stated options: 220 V, 415 V, 460 V, 690 V and 60 Hz
Confirm the applicable design code, flange rating, motor voltage and rotation direction for the specific model and order.
Structural Drawings

Performance Data Tables
|
Model |
Flow rate (m³/h) |
Head (m) |
Speed (r/min) |
Efficiency (%) |
Shaft power (kW) |
Motor power (kW) |
NPSHr (m) |
Impeller diameter (mm) |
Inlet diameter (mm) |
Outlet diameter (mm) |
|
CZ32-160 |
20 |
36 |
2950 |
- |
- |
4 |
- |
- |
50 |
32 |
|
CZ32-160 |
20 |
36 |
2950 |
- |
- |
5.5 |
- |
- |
- |
- |
|
CZ32-200 |
20 |
51.8 |
2950 |
51 |
- |
7.5 |
2 |
- |
- |
- |
|
CZ32-200 |
9 |
60 |
2900 |
- |
- |
5.5 |
- |
- |
- |
- |
|
CZ40-160 |
30 |
34 |
2900 |
63 |
4.41 |
7.5 |
1.5 |
169 |
65 |
40 |
|
CZ40-200 |
34 |
51.5 |
2900 |
60 |
7.95 |
11 |
2.4 |
209 |
65 |
40 |
|
CZ40-250 |
38 |
85 |
2900 |
50 |
17.6 |
22 |
5.1 |
259 |
- |
- |
|
CZ50-160 |
58 |
34 |
2900 |
73 |
7.36 |
11 |
2.9 |
169 |
80 |
50 |
|
CZ50-200 |
67.5 |
55.5 |
2900 |
72 |
14.2 |
15 |
3.4 |
209 |
80 |
50 |
|
CZ50-250 |
67.5 |
85 |
2900 |
64 |
24.4 |
30 |
3 |
259 |
- |
- |
|
CZ65-160 |
105 |
32 |
2900 |
74 |
12.4 |
15 |
2.7 |
169 |
100 |
65 |
|
CZ65-200 |
107 |
52 |
2900 |
73 |
20.8 |
30 |
2.8 |
209 |
100 |
65 |
|
CZ65-250 |
115 |
85 |
2900 |
71 |
37.5 |
45 |
3.4 |
259 |
- |
- |
|
CZ65-250 |
115 |
80 |
2900 |
- |
- |
- |
- |
- |
- |
- |
|
CZ80-160 |
175 |
27 |
2900 |
76 |
16.9 |
18.5 |
4 |
169 |
125 |
80 |
|
CZ80-200 |
156 |
51 |
2900 |
79 |
27.4 |
37 |
3.5 |
209 |
125 |
80 |
|
CZ80-250 |
190 |
82.5 |
2900 |
80 |
53.4 |
75 |
5 |
259 |
- |
- |
|
CZ100-200 |
225 |
45 |
2900 |
81 |
34.1 |
45 |
4 |
209 |
125 |
100 |
|
CZ100-250 |
282 |
75 |
2900 |
81.5 |
70.7 |
90 |
6 |
259 |
- |
- |
|
CZ100-315 |
275 |
138 |
2900 |
75.5 |
137 |
160 |
5.8 |
324 |
125 |
100 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: cz chemical process pump, China cz chemical process pump manufacturers, factory


