Product Overview
The NYP series is a positive-displacement internal-gear rotor pump developed for industries such as petroleum, chemicals, coatings, oils and fats, pharmaceuticals, dyes and food processing. Its main components include an inner rotor, outer rotor, shaft, casing, cover, bearing bracket and shaft seal. Material and seal options allow the pump to be configured for different liquids and operating conditions.
The pump is a horizontal internal-gear design. Two rotor profiles are described in the source: one uses a cycloidal inner rotor with an arc-profile outer rotor; the other uses cycloidal profiles for both rotors. The source states that the two designs have the same performance and installation dimensions.
A crescent-shaped partition separates the suction and discharge chambers. As the inner and outer rotors turn in the same direction, liquid is drawn into the expanding spaces between the rotor teeth, carried through the casing and discharged as those spaces contract.
The stated viscosity range is 0.02–200 Pa·s, equivalent to 20–200,000 cP.
Model designation example: NYP 220/1.0
- NYP: High-viscosity rotor-pump series.
- 220: Rated flow, in L/min.
- 1.0: Rated working pressure, in MPa.
Product Features
1. Suitable for highly viscous liquids
The pump is intended for liquids with viscosities up to 200,000 cP under suitable operating conditions. Lower speed may allow it to handle more viscous material, but achievable flow and motor load depend on the liquid, temperature, suction conditions and pump configuration.
2. Smooth positive-displacement transfer
The internal-gear arrangement provides steady displacement and can be suitable for shear-sensitive products such as polymer solutions, emulsions and food pastes. Shear is reduced in suitable operating conditions, not eliminated; its actual effect depends on the rotor design, speed and product properties.
3. Reversible operation may be available
The source describes reverse rotation for clearing or flushing a line. Confirm that the specific pump, seal arrangement, relief-valve arrangement and motor setup permit reverse operation before using this feature.
4. Self-priming capability
The stated self-priming height is up to 8.5 m. This is a nominal figure: viscosity, liquid temperature, suction-line losses, air leakage and priming conditions can substantially reduce achievable suction lift.
5. Multiple drive arrangements
Available arrangements include direct motor drive, VFD speed control and belt drive. Since flow generally varies with speed, a VFD can be used to adjust delivery, subject to the pump's allowable speed range and the motor's operating limits.
6. High-temperature options
The source gives a standard operating temperature of up to 250°C, with special configurations up to 350°C. High-temperature service requires the correct rotor and casing materials, shaft-seal arrangement, clearances, bearing design and thermal management.
7. Options for gas–liquid mixtures and limited solids
The pump may handle gas–liquid mixtures or liquids containing small quantities of solids when designed for the specific duty. Confirm the permitted gas fraction, particle size and solids concentration with the manufacturer.
8. Broad material and sealing options
Wetted parts can be specified in carbon steel, cast iron, stainless steel, duplex stainless steel, high-nickel alloys or titanium, subject to chemical compatibility. Shaft seals may be mechanical, packed or double mechanical seals.
Applications
The NYP series is used for viscous liquids and, with an appropriate configuration, high-temperature service:
- Petroleum and chemicals: Crude oil, heavy oil, bitumen, coal tar, paraffin, lubricating grease, catalysts, polyols and chemical-fibre feedstocks.
- Polymers: Rubber, resin, plastics, synthetic-fibre polymer solutions and slurries.
- Food and brewing: Chocolate, syrup, honey, fruit purée, oils, starch paste, yeast and spent-grain products, subject to hygienic design and approvals.
- Pharmaceuticals and cosmetics: Ointments, creams, emulsions, shampoo and facial cleansers, subject to process requirements.
- Paper and coatings: Pulp, black liquor, coatings, paint, ink and pigment products.
- Specialty chemicals and building materials: Polyurethane, adhesives, sealants, bituminous coatings and sodium silicate.
- Household chemicals: Soap, detergent slurry and textile sizing.
- Other services: Sludge transfer in wastewater treatment and coal–water slurry service in power plants, subject to pump configuration and wear considerations.
Technical Specifications
1. Design Standard
The supplied material cites JB/T 8091, Screw Pumps. Because that standard's scope may not match an internal-gear rotor pump, confirm the applicable design, testing and acceptance standards with the manufacturer for the specific product.
2. Operating Principle
The NYP pump is a rotary positive-displacement internal-gear pump. The inner rotor drives the outer rotor in the same direction.
On the suction side, the rotor teeth move out of engagement and the spaces between them expand, drawing liquid into the pump. The liquid is carried in the spaces between the rotor teeth and the casing toward the discharge side. As the teeth re-engage, the spaces contract and the liquid is displaced into the outlet.
3. Construction and Connections
The pump is a horizontal internal-gear design. The source describes two rotor-profile arrangements: cycloidal inner rotor with arc-profile outer rotor, or cycloidal profiles for both rotors. Inlet and outlet connections may be flanged or threaded, and their orientation can be adapted to suit the pipe layout where the design permits.
4. Shaft-Seal Options
Seal selection depends on the medium, temperature, pressure and leakage-control requirements:
- Mechanical seal: For general service when suitable materials are selected.
- Packing seal: A simpler arrangement for appropriate applications.
- Double mechanical seal: For service requiring additional leakage control.
- High-temperature seal configuration: A cooled seal chamber or other thermal-management arrangement may be recommended for high-temperature duties.
5. Heating and Insulation
The casing and cover can be fitted with a heating jacket. Steam or thermal oil may be circulated through the jacket to keep viscous liquids sufficiently warm to flow. Jacket connections and heating conditions should be specified to suit the process and the pump design.
6. Wetted-Part Material Options
|
Material |
General selection guidance |
|
Carbon steel |
General neutral liquids, lubricating oil and heavy oil |
|
Cast iron |
General viscous-liquid service where chemical compatibility is suitable |
|
304 stainless steel |
Selected mildly corrosive or food-contact applications, subject to compatibility and hygiene requirements |
|
316 / 316L stainless steel |
Selected chloride-bearing or more corrosive service; actual suitability depends on concentration and temperature |
|
2205 duplex stainless steel |
Some demanding corrosive and abrasive applications |
|
904-series stainless steel |
Selected severe-corrosion duties after compatibility review |
|
Hastelloy-type alloys |
Special corrosive media, selected by chemical compatibility |
|
Titanium |
Selected corrosive or high-temperature applications where compatible |
Stainless-steel grades do not have a universal pH service range. Check the exact fluid composition, concentration, temperature and contaminants before selecting materials. Food-contact suitability also requires appropriate surface finish, seals and certifications.
7. Drive Options
Direct motor drive: Compact arrangement with high transmission efficiency.
VFD drive: Allows variable-speed operation for flow adjustment within the approved operating range.
Belt drive: Permits speed changes by changing pulley ratios and may suit applications requiring reduced speed.
8. Stated Operating Range
|
Parameter |
Stated range |
|
Flow rate, Q |
0.1–1,000 m³/h across the series |
|
Working pressure |
Up to 4.0 MPa; higher pressure may be available by special design |
|
Viscosity |
20–200,000 cP (equivalent to 0.02–200 Pa·s in the product description) |
|
Medium temperature |
−30°C to 250°C; up to 350°C for special configurations |
|
Speed, n |
100–960 r/min |
|
Self-priming height |
Up to 8.5 m, as stated; actual suction lift depends on duty conditions |
|
Motor power |
0.55–400 kW, selected for the operating point |
|
Drive |
Direct drive, VFD drive or belt drive |
|
Shaft seal |
Mechanical, packing or double mechanical seal |
|
Heating jacket |
Optional; steam or thermal oil |
Structural Drawings

Performance Data Tables
|
Model |
Theoretical displacement (L/100 rev) |
Flow rate (m³/h) |
Working pressure (MPa) |
Speed (r/min) |
Motor power (kW) |
Maximum viscosity (cSt) |
Inlet diameter (mm) |
Outlet diameter (mm) |
Weight (kg) |
|
NYP3/0.6 |
3 |
0.3~0.7 |
0.6 |
200~500 |
0.55~0.75 |
100000 |
25 |
25 |
35 |
|
NYP3/1.0 |
3 |
0.3~0.7 |
1 |
200~500 |
0.75~1.1 |
100000 |
25 |
25 |
38 |
|
NYP3/1.6 |
3 |
0.3~0.7 |
1.6 |
200~500 |
1.1~1.5 |
100000 |
25 |
25 |
40 |
|
NYP6/0.6 |
6 |
0.6~1.4 |
0.6 |
200~500 |
0.75~1.1 |
200000 |
32 |
25 |
45 |
|
NYP6/1.0 |
6 |
0.6~1.4 |
1 |
200~500 |
1.1~1.5 |
200000 |
32 |
25 |
50 |
|
NYP6/1.6 |
6 |
0.6~1.4 |
1.6 |
200~500 |
1.5~2.2 |
200000 |
32 |
25 |
55 |
|
NYP6/2.5 |
6 |
0.6~1.4 |
2.5 |
200~500 |
2.2~3.0 |
200000 |
32 |
25 |
60 |
|
NYP12/0.6 |
12 |
1.2~3.0 |
0.6 |
200~500 |
1.1~1.5 |
300000 |
40 |
32 |
55 |
|
NYP12/1.0 |
12 |
1.2~3.0 |
1 |
200~500 |
1.5~2.2 |
300000 |
40 |
32 |
60 |
|
NYP12/1.6 |
12 |
1.2~3.0 |
1.6 |
200~500 |
2.2~3.0 |
300000 |
40 |
32 |
65 |
|
NYP12/2.5 |
12 |
1.2~3.0 |
2.5 |
200~500 |
3.0~4.0 |
300000 |
40 |
32 |
70 |
|
NYP20/0.6 |
20 |
2.0~5.0 |
0.6 |
200~500 |
1.5~2.2 |
500000 |
50 |
40 |
70 |
|
NYP20/1.0 |
20 |
2.0~5.0 |
1 |
200~500 |
2.2~3.0 |
500000 |
50 |
40 |
75 |
|
NYP20/1.6 |
20 |
2.0~5.0 |
1.6 |
200~500 |
3.0~4.0 |
500000 |
50 |
40 |
80 |
|
NYP20/2.5 |
20 |
2.0~5.0 |
2.5 |
200~500 |
4.0~5.5 |
500000 |
50 |
40 |
90 |
|
NYP36/0.6 |
36 |
3.5~9.0 |
0.6 |
200~500 |
2.2~3.0 |
800000 |
65 |
50 |
90 |
|
NYP36/1.0 |
36 |
3.5~9.0 |
1 |
200~500 |
3.0~4.0 |
800000 |
65 |
50 |
95 |
|
NYP36/1.6 |
36 |
3.5~9.0 |
1.6 |
200~500 |
4.0~5.5 |
800000 |
65 |
50 |
105 |
|
NYP36/2.5 |
36 |
3.5~9.0 |
2.5 |
200~500 |
5.5~7.5 |
800000 |
65 |
50 |
115 |
|
NYP52/0.6 |
52 |
5.0~13.0 |
0.6 |
200~500 |
3.0~4.0 |
1000000 |
80 |
65 |
115 |
|
NYP52/1.0 |
52 |
5.0~13.0 |
1 |
200~500 |
4.0~5.5 |
1000000 |
80 |
65 |
125 |
|
NYP52/1.6 |
52 |
5.0~13.0 |
1.6 |
200~500 |
5.5~7.5 |
1000000 |
80 |
65 |
135 |
|
NYP52/2.5 |
52 |
5.0~13.0 |
2.5 |
200~500 |
7.5~11.0 |
1000000 |
80 |
65 |
150 |
|
NYP80/0.6 |
80 |
8.0~20.0 |
0.6 |
200~500 |
4.0~5.5 |
1500000 |
100 |
80 |
145 |
|
NYP80/1.0 |
80 |
8.0~20.0 |
1 |
200~500 |
5.5~7.5 |
1500000 |
100 |
80 |
155 |
|
NYP80/1.6 |
80 |
8.0~20.0 |
1.6 |
200~500 |
7.5~11.0 |
1500000 |
100 |
80 |
170 |
|
NYP80/2.5 |
80 |
8.0~20.0 |
2.5 |
200~500 |
11.0~15.0 |
1500000 |
100 |
80 |
190 |
|
NYP110/0.6 |
110 |
11.0~28.0 |
0.6 |
200~500 |
5.5~7.5 |
2000000 |
125 |
100 |
185 |
|
NYP110/1.0 |
110 |
11.0~28.0 |
1 |
200~500 |
7.5~11.0 |
2000000 |
125 |
100 |
200 |
|
NYP110/1.6 |
110 |
11.0~28.0 |
1.6 |
200~500 |
11.0~15.0 |
2000000 |
125 |
100 |
220 |
|
NYP110/2.5 |
110 |
11.0~28.0 |
2.5 |
200~500 |
15.0~18.5 |
2000000 |
125 |
100 |
240 |
|
NYP160/0.6 |
160 |
16.0~40.0 |
0.6 |
200~500 |
7.5~11.0 |
3000000 |
150 |
125 |
240 |
|
NYP160/1.0 |
160 |
16.0~40.0 |
1 |
200~500 |
11.0~15.0 |
3000000 |
150 |
125 |
260 |
|
NYP160/1.6 |
160 |
16.0~40.0 |
1.6 |
200~500 |
15.0~18.5 |
3000000 |
150 |
125 |
285 |
|
NYP160/2.5 |
160 |
16.0~40.0 |
2.5 |
200~500 |
18.5~22.0 |
3000000 |
150 |
125 |
310 |
|
NYP220/0.6 |
220 |
22.0~55.0 |
0.6 |
200~500 |
11.0~15.0 |
5000000 |
200 |
150 |
320 |
|
NYP220/1.0 |
220 |
22.0~55.0 |
1 |
200~500 |
15.0~18.5 |
5000000 |
200 |
150 |
345 |
|
NYP220/1.6 |
220 |
22.0~55.0 |
1.6 |
200~500 |
18.5~22.0 |
5000000 |
200 |
150 |
370 |
|
NYP220/2.5 |
220 |
22.0~55.0 |
2.5 |
200~500 |
22.0~30.0 |
5000000 |
200 |
150 |
400 |
|
NYP320/0.6 |
320 |
32.0~80.0 |
0.6 |
200~400 |
15.0~18.5 |
8000000 |
250 |
200 |
420 |
|
NYP320/1.0 |
320 |
32.0~80.0 |
1 |
200~400 |
18.5~22.0 |
8000000 |
250 |
200 |
450 |
|
NYP320/1.6 |
320 |
32.0~80.0 |
1.6 |
200~400 |
22.0~30.0 |
8000000 |
250 |
200 |
480 |
|
NYP440/0.6 |
440 |
44.0~110.0 |
0.6 |
200~350 |
18.5~22.0 |
10000000 |
300 |
250 |
530 |
|
NYP440/1.0 |
440 |
44.0~110.0 |
1 |
200~350 |
22.0~30.0 |
10000000 |
300 |
250 |
570 |
|
NYP440/1.6 |
440 |
44.0~110.0 |
1.6 |
200~350 |
30.0~37.0 |
10000000 |
300 |
250 |
610 |
|
NYP660/0.6 |
660 |
66.0~160.0 |
0.6 |
200~300 |
22.0~30.0 |
10000000 |
350 |
300 |
650 |
|
NYP660/1.0 |
660 |
66.0~160.0 |
1 |
200~300 |
30.0~37.0 |
10000000 |
350 |
300 |
700 |
|
NYP880/0.6 |
880 |
88.0~200.0 |
0.6 |
200~250 |
30.0~37.0 |
10000000 |
400 |
350 |
800 |
|
NYP880/1.0 |
880 |
88.0~200.0 |
1 |
200~250 |
37.0~45.0 |
10000000 |
400 |
350 |
860 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: nyp high-viscosity rotor pump, China nyp high-viscosity rotor pump manufacturers, factory


