Product Overview
The YLB Filter Press Feed Pump is a newly developed, leak-free pump based on German pump technology. It was designed jointly by a pump design institute and the Institute of Fluid Machinery at Jiangsu University of Technology to meet users' actual operating requirements.
Its rated performance points and dimensions comply with the international standard ISO 2858:1975(E). The YLB is an upgraded replacement for enamel-lined pumps, ceramic pumps, rubber-lined pumps, fluoropolymer-alloy pumps, F-type corrosion-resistant pumps and IH chemical-process centrifugal pumps.
The YLB is a horizontal, single-stage, single-suction centrifugal pump. It is designed to address common problems encountered with conventional pump types under demanding service conditions, including seal leakage, rapid wear of wetted components, and short seal life when handling solids-bearing media at high pressure.
- Example of model designation: YLB 50-40-K
- YLB: Pump designed for filter press applications
- 50: Suction inlet diameter (mm)
- 40: Head (m)
- K: Open impeller
The YLB is available in two speed and pressure-rating ranges: a high-speed series with a rated speed of 2,900 r/min, and a low-speed series with a rated speed of 1,450 r/min.
The low-speed series is designed for slurries containing larger particles, including sand- or gravel-bearing slurries. Its large flow passages allow larger particles entering the pump chamber to be promptly discharged by the open impeller, helping prevent wear caused by particle retention and blockages between the impeller, pump cover and casing.
Both series use an open impeller (K type). The low-speed series is particularly suited to high-solids and highly abrasive service.
Product Features
1. Rear-suction design with negative-pressure sealing
The suction inlet and shaft seal are oriented in the same direction. In this rear-suction design, the seal is located in the negative-pressure zone created by impeller rotation. During filter press operation, as pressure rises and flow decreases, the mechanical seal is not subjected to the pressure of the pumped medium. This helps ensure reliable, leak-free sealing over extended operation.
2. Open impeller with wide passages to help prevent clogging
The pump features a rear-open impeller design with wide, unobstructed flow passages. This helps resist clogging and crystallization and allows the pump to handle particle-laden media.
When larger sand or gravel particles enter the pump chamber, the open impeller can promptly discharge them. This helps prevent particle retention, excessive wear or jamming between the impeller, pump cover and casing-an operating capability not typically offered by standard centrifugal pumps.
3. Two speed ranges for different wear-resistance requirements
The high-speed series is suitable for applications with typical solids content. The low-speed series, operating at 1,450 r/min, offers improved wear resistance and is designed for media containing sand, gravel or larger particles, extending the pump's range of applications.
4. Split wear-part construction for economical maintenance
The pump cover and suction inlet use a split construction with replaceable corrosion- and abrasion-resistant wear parts. When wear occurs, only the affected components need to be replaced, reducing maintenance costs.
The seal does not use a back impeller for pressure reduction, helping to reduce shaft power consumption and operating energy costs.
5. Material options for a wide range of corrosive media
Pump materials can be selected to suit the media handled by the filter press. Available materials include:
1Cr18Ni9Ti, 1Cr18Ni12Mo2Ti, 304, 304L, 316L, duplex stainless steel, F46 (fluoropolymer alloy), ultra-high-molecular-weight polyethylene (UHMWPE), reinforced polypropylene, Monel and Hastelloy.
Spare parts made from different materials offer good interchangeability, making material changes and maintenance convenient.
6. Smooth, quiet operation and long service life
The bearing-frame assembly uses multiple high-quality bearings, typically three imported bearings. Its extended bearing frame supports smooth, quiet operation, reliable sealing, straightforward maintenance and long service life.
7. High-performance seal materials
The seal faces use high-quality solid cemented-carbide rings, providing excellent wear, corrosion and heat resistance. Seal service life is significantly longer than that of conventional pump designs.
8. Wide performance range for flexible selection
The pump covers a flow range of 6.3–200 m³/h and a head range of 5–125 m. It is available at speeds of 2,900 r/min and 1,450 r/min to suit different filter press operating conditions.
Applications
The YLB Filter Press Feed Pump is widely used in the chemical, petroleum, starch, pharmaceutical, dye, paint, metallurgical, pulp and paper, electroplating, power generation and food industries. It is primarily designed to convey abrasive and corrosive slurries, suspensions or viscous liquids with a solids content of 1%–60%, including feed service for filter presses.
Typical applications include:
- Filter press feed: Pressurized feed for plate-and-frame, chamber and belt filter presses. The pump is designed to maintain stable pressure and leak-free operation as filtration pressure rises and flow gradually decreases.
- Non-ferrous metal hydrometallurgy: Transfer of electrolytes used in copper and nickel production, acid-bearing liquids in cobalt production, and ore slurries in zinc production.
- Environmental protection: High-pressure transfer of sludge and waste residues during filter pressing.
- Flue gas desulfurization and air-pollution control: Pressurized spraying, washing and other sustained-pressure operations.
- Alkali production: Transfer of ammoniated brine mother liquor in soda ash and combined ammonia-soda processes, as well as ambient-temperature caustic soda and hypochlorite solutions in chlor-alkali production.
- Fertilizer and acid production: Transfer of media such as nitric acid, sulfuric acid, hydrochloric acid, phosphoric acid, urea and ammonium nitrate.
- Pulp and paper: Transfer of pulp-cooking liquor and pulp-bleaching liquor.
- Iron and steel production: Electroplating, pickling and waste-acid treatment.
Technical Specifications
1. Design Principle and Construction
The YLB Filter Press Feed Pump is a newly developed, lined, rear-suction pump designed for leak-free operation with corrosive and abrasive media. In this design, the shaft seal and suction inlet are oriented in the same direction.
To address the seal leakage commonly experienced with conventional corrosion- and abrasion-resistant slurry pumps, the suction inlet is positioned on the side of the pump chamber, between the impeller eye and the sealing assembly. This arrangement creates a negative-pressure zone at the seal, so the sealing assembly is subjected to little or no liquid pressure during operation. It helps overcome the leakage that can occur when conventional pumps operate above 0.6 MPa, significantly improving seal service life and reliability.
The pump is a horizontal, single-stage, single-suction, cantilever centrifugal pump fitted with an open impeller (K type). The casing is typically made of steel lined with ultra-high-molecular-weight polyethylene (UHMWPE), or with another corrosion-resistant lining. Materials for the wetted components and sealing assembly can be selected to suit the properties of the pumped medium.
2. Design and Manufacturing Standards
The pump's rated performance points and dimensions comply with ISO 2858:1975(E). Products can also be manufactured in accordance with Chinese GB and HG standards, as well as U.S. API standards.
3. Shaft-Seal System and Sealing Options
The pump can be supplied with mechanical, power or packing seals. The negative-pressure mechanical seal is a key feature of the design.
a. Negative-pressure sealing principle
The impeller eye faces the seal, while the pump casing's suction inlet is located on the side of the pump chamber. This places the seal in a negative-pressure zone and prevents it from being subjected to high-pressure process liquid.
b. Seal materials
The rotating and stationary seal faces use solid cemented-carbide rings in a hard-on-hard configuration, providing strong corrosion and wear resistance.
c. Cooling requirements
For seal arrangements requiring cooling water, start the cooling-water supply before starting the pump. The typical supply pressure is 0.1–0.3 MPa. Shut off the cooling water only after disconnecting power to the motor.
4. Operating Conditions
- Flow rate (Q): 6.3–200 m³/h; up to 400 m³/h for some series
- Head (H): 5–125 m; maximum head is also stated as up to 90 m
- Working pressure (P): ≤2.4 MPa, casing design pressure
- Speed (n): 2,900 or 1,450 r/min; high- and low-speed series
- Medium temperature: −10°C to 110°C; up to 180°C with certain materials, depending on wetted-part materials
- Solids content: 1%–60%, depending on lining material and impeller type
- Motor power: 4–75 kW, selected based on operating conditions; some low-speed models use lower-power motors
- Inlet diameter: 40–125 mm; outlet diameter selected to match
5. Material Options
The YLB pump offers a wide selection of materials for wetted components:
- Duplex stainless steel and alloy steel: For corrosive chemical slurries requiring wear resistance.
- UHMWPE: Excellent corrosion and wear resistance, long service life and good cost-effectiveness.
- F46 fluoropolymer alloy: For highly corrosive and high-temperature service, including strong acids and alkalis.
- Reinforced polypropylene: A cost-effective option for general service.
- Monel and Hastelloy: For demanding applications requiring high-temperature, corrosion and wear resistance.
6. Application Limitations
The pump is not suitable for applications where the liquid level at the suction inlet is more than 1.2 m below the pump, or where suction-side vacuum is excessive.
For pumps fitted with seals that require cooling water, start the cooling-water supply before starting the pump.
7. General Performance Range
- Flow rate (Q): 6.3–200 m³/h; up to 400 m³/h
- Head (H): 5–125 m; maximum single-stage head approximately 90 m
- Speed (n): 2,900 or 1,450 r/min
- Working pressure (P): ≤2.4 MPa, design pressure
- Medium temperature: −10°C to 110°C; up to 180°C with special materials
- Solids content: 1%–60%
- Motor power: 4–75 kW, selected according to medium density and operating conditions
- Inlet diameter: 40–125 mm
- Design standard: ISO 2858:1975(E)
Structural Drawings

Performance Data Tables
|
Model |
Speed (r/min) |
Flow rate, Q (m³/h) |
Head, H (m) |
Efficiency, η (%) |
Shaft power (kW) |
Motor power (kW) |
Required NPSH (m) |
Pump weight (kg) |
|
YLB50-32-125 |
2900 |
12.5 |
20 |
51 |
1.33 |
2.2 |
2 |
45 |
|
1450 |
6.3 |
5 |
45 |
0.19 |
0.55 |
2 |
45 |
|
|
YLB50-32-125A |
2900 |
11.3 |
16.4 |
50 |
1.01 |
1.5 |
2 |
45 |
|
1450 |
5.7 |
4.1 |
43 |
0.15 |
0.55 |
2 |
45 |
|
|
YLB50-32-160 |
2900 |
12.5 |
32 |
46 |
2.37 |
3 |
2 |
49 |
|
1450 |
6.3 |
8 |
40 |
0.34 |
0.55 |
2 |
49 |
|
|
YLB50-32-160A |
2900 |
11.3 |
26.4 |
44 |
1.85 |
3 |
2 |
49 |
|
1450 |
5.7 |
6.6 |
37.1 |
0.28 |
0.55 |
2 |
49 |
|
|
YLB50-32-200 |
2900 |
12.5 |
50 |
39 |
4.36 |
5.5 |
2 |
59 |
|
1450 |
6.3 |
12.5 |
33 |
0.65 |
1.1 |
2 |
59 |
|
|
YLB50-32-200A |
2900 |
11.3 |
41 |
38 |
3.32 |
4 |
2 |
59 |
|
1450 |
5.7 |
10.3 |
31 |
0.52 |
0.75 |
2 |
59 |
|
|
YLB50-32-250 |
2900 |
12.5 |
80 |
33 |
8.25 |
11 |
2 |
92 |
|
1450 |
6.3 |
20 |
27 |
1.27 |
2.2 |
2 |
92 |
|
|
YLB50-32-250A |
2900 |
11.7 |
70 |
32 |
6.97 |
11 |
2 |
92 |
|
1450 |
5.9 |
17.5 |
25 |
1.12 |
1.5 |
2 |
92 |
|
|
YLB50-32-250B |
2900 |
11 |
62 |
30 |
6.19 |
7.5 |
2 |
92 |
|
YLB65-50-125 |
2900 |
25 |
20 |
62 |
2.2 |
3 |
2 |
46 |
|
1450 |
12.5 |
5 |
55 |
0.31 |
0.55 |
2 |
46 |
|
|
YLB65-50-125A |
2900 |
22.7 |
16.5 |
61 |
1.67 |
2.2 |
2 |
46 |
|
1450 |
11.3 |
4.1 |
54 |
0.23 |
0.55 |
2 |
46 |
|
|
YLB65-50-160 |
2900 |
25 |
32 |
57 |
3.82 |
5.5 |
2 |
52 |
|
1450 |
12.5 |
8 |
51 |
0.53 |
0.75 |
2 |
52 |
|
|
YLB65-50-160A |
2900 |
22.7 |
26.5 |
56 |
2.93 |
4 |
2 |
52 |
|
1450 |
11.3 |
6.6 |
49.6 |
0.41 |
0.55 |
2 |
52 |
|
|
YLB65-40-200 |
2900 |
25 |
50 |
52 |
6.55 |
11 |
2 |
62 |
|
1450 |
12.5 |
12.5 |
46 |
0.93 |
1.5 |
2 |
62 |
|
|
YLB65-40-200A |
2900 |
22.7 |
41 |
50 |
5.07 |
7.5 |
2 |
62 |
|
1450 |
11.3 |
10.3 |
44 |
0.72 |
1.1 |
2 |
62 |
|
|
YLB65-40-250 |
2900 |
25 |
80 |
46 |
11.84 |
15 |
2 |
98 |
|
1450 |
12.5 |
20 |
39 |
1.75 |
3 |
2 |
98 |
|
|
YLB65-40-250A |
2900 |
23.4 |
74.8 |
45 |
10.59 |
15 |
2 |
98 |
|
1450 |
11.7 |
17.5 |
37.9 |
1.47 |
2.2 |
2 |
98 |
|
|
YLB65-40-315 |
2900 |
25 |
125 |
39 |
21.83 |
30 |
2 |
115 |
|
1450 |
12.5 |
32 |
33 |
3.3 |
5.5 |
2 |
115 |
|
|
YLB65-40-315A |
2900 |
23.4 |
109.5 |
38 |
18.37 |
30 |
2 |
115 |
|
1450 |
11.7 |
28 |
33 |
2.7 |
4 |
2 |
115 |
|
|
YLB80-65-125 |
2900 |
50 |
20 |
69 |
3.95 |
5.5 |
3 |
52 |
|
1450 |
25 |
5 |
64 |
0.53 |
0.75 |
2.5 |
52 |
|
|
YLB80-65-125A |
2900 |
45.3 |
16.5 |
67 |
3.04 |
4 |
3 |
52 |
|
1450 |
22.7 |
4.1 |
62 |
0.41 |
0.55 |
2.5 |
52 |
|
|
YLB80-65-160 |
2900 |
50 |
32 |
67 |
6.5 |
11 |
2.3 |
60 |
|
1450 |
25 |
8 |
62 |
0.88 |
1.5 |
2 |
60 |
|
|
YLB80-65-160A |
2900 |
45.3 |
26.5 |
66 |
4.95 |
7.5 |
2.3 |
60 |
|
1450 |
22.7 |
6.6 |
60 |
0.68 |
1.1 |
2 |
60 |
|
|
YLB80-50-200 |
2900 |
50 |
50 |
63 |
10.81 |
15 |
2.5 |
72 |
|
1450 |
25 |
12.5 |
57 |
1.49 |
2.2 |
2 |
72 |
|
|
YLB80-50-200A |
2900 |
45.3 |
41 |
62 |
8.16 |
11 |
2.5 |
72 |
|
1450 |
22.7 |
10.3 |
55 |
1.16 |
1.5 |
2 |
72 |
|
|
YLB80-50-250 |
2900 |
50 |
80 |
57 |
19.11 |
30 |
2.5 |
110 |
|
1450 |
25 |
20 |
52 |
2.62 |
4 |
2 |
110 |
|
|
YLB80-50-250A |
2900 |
46.8 |
70 |
56 |
15.93 |
22 |
2.5 |
110 |
|
1450 |
23.4 |
17.5 |
50 |
2.23 |
3 |
2 |
110 |
|
|
YLB80-50-315 |
2900 |
50 |
125 |
52 |
32.73 |
45 |
2.5 |
128 |
|
1450 |
25 |
32 |
47 |
4.63 |
7.5 |
2 |
128 |
|
|
YLB80-50-315A |
2900 |
46.8 |
109.5 |
51 |
27.36 |
37 |
2.5 |
128 |
|
1450 |
23.4 |
28 |
45 |
3.96 |
5.5 |
2 |
128 |
|
|
YLB100-80-125 |
2900 |
100 |
20 |
73 |
7.46 |
11 |
4.3 |
68 |
|
1450 |
50 |
5 |
69 |
0.99 |
1.5 |
2.5 |
68 |
|
|
YLB100-80-125A |
2900 |
90.8 |
16.5 |
71 |
5.75 |
7.5 |
4.3 |
68 |
|
1450 |
45.4 |
4.1 |
67 |
0.76 |
1.1 |
2.5 |
68 |
|
|
YLB100-80-160 |
2900 |
100 |
32 |
73 |
11.94 |
15 |
4 |
78 |
|
1450 |
50 |
8 |
69 |
1.58 |
2.2 |
2.5 |
78 |
|
|
YLB100-80-160A |
2900 |
90.8 |
26.5 |
71 |
9.23 |
11 |
4 |
78 |
|
1450 |
45.4 |
6.6 |
67 |
1.22 |
1.5 |
2.5 |
78 |
|
|
YLB100-65-200 |
2900 |
100 |
50 |
73 |
18.65 |
30 |
3.9 |
90 |
|
1450 |
50 |
12.5 |
68 |
2.5 |
4 |
2.5 |
90 |
|
|
YLB100-65-200A |
2900 |
90.8 |
41 |
71 |
14.28 |
22 |
3.9 |
90 |
|
1450 |
45.4 |
10.3 |
66 |
1.93 |
3 |
2.5 |
90 |
|
|
YLB100-65-250 |
2900 |
100 |
80 |
68 |
32.03 |
45 |
3.6 |
125 |
|
1450 |
50 |
20 |
63 |
4.32 |
7.5 |
2.5 |
125 |
|
|
YLB100-65-250A |
2900 |
93.5 |
70 |
67 |
26.6 |
37 |
3.6 |
125 |
|
1450 |
46.8 |
17.5 |
61 |
3.66 |
5.5 |
2.5 |
125 |
|
|
YLB100-65-315 |
2900 |
100 |
125 |
62 |
54.88 |
75 |
3.6 |
142 |
|
1450 |
50 |
32 |
58 |
7.51 |
11 |
2.5 |
142 |
|
|
YLB100-65-315A |
2900 |
93.5 |
109.5 |
61 |
45.71 |
55 |
3.6 |
142 |
|
1450 |
46.8 |
28 |
56 |
6.37 |
11 |
2.5 |
142 |
|
|
YLB125-100-200 |
2900 |
200 |
50 |
77 |
35.35 |
45 |
5 |
98 |
|
1450 |
100 |
12.5 |
73 |
4.66 |
7.5 |
2.8 |
98 |
|
|
YLB125-100-200A |
2900 |
181.6 |
41 |
75 |
27.03 |
37 |
5 |
98 |
|
1450 |
90.8 |
10.3 |
71 |
3.59 |
5.5 |
2.8 |
98 |
|
|
YLB125-100-250 |
2900 |
200 |
80 |
72 |
60.49 |
75 |
4.5 |
135 |
|
1450 |
100 |
20 |
70 |
7.78 |
15 |
2.5 |
135 |
|
|
YLB125-100-250A |
2900 |
187 |
70 |
71 |
50.19 |
55 |
4.5 |
135 |
|
1450 |
93.5 |
17.5 |
68 |
6.55 |
11 |
2.5 |
135 |
|
|
YLB125-100-315 |
2900 |
200 |
125 |
68 |
100.06 |
132 |
4.2 |
155 |
|
1450 |
100 |
32 |
65 |
13.4 |
22 |
2.5 |
155 |
|
|
YLB125-100-315A |
2900 |
187 |
109.5 |
67 |
83.21 |
110 |
4.2 |
155 |
|
1450 |
93.5 |
28 |
63 |
11.31 |
18.5 |
2.5 |
155 |
|
|
YLB125-100-400 |
1450 |
100 |
50 |
62 |
21.96 |
30 |
2.5 |
220 |
|
YLB125-100-400A |
1450 |
118 |
43.7 |
61 |
18.24 |
30 |
2.5 |
220 |
|
YLB150-125-250 |
1450 |
200 |
22 |
77 |
14.16 |
18.5 |
2.8 |
175 |
|
YLB150-125-250A |
1450 |
150 |
10 |
- |
- |
11 |
- |
- |
|
YLB150-125-315 |
1450 |
200 |
32 |
72 |
24.2 |
30 |
2.8 |
200 |
|
YLB150-125-315A |
1450 |
112 |
32.3 |
62 |
15.92 |
30 |
2.5 |
200 |
|
YLB150-125-400 |
1450 |
200 |
50 |
70 |
38.89 |
55 |
2.8 |
260 |
|
YLB150-125-400A |
1450 |
187 |
44 |
68 |
32.95 |
45 |
2.8 |
260 |
|
YLB200-150-250 |
1450 |
400 |
20 |
79 |
27.57 |
37 |
3.5 |
230 |
|
YLB200-150-250A |
1450 |
372 |
17 |
77 |
22.36 |
30 |
3.5 |
230 |
|
YLB200-150-315 |
1450 |
400 |
32 |
77 |
45.24 |
75 |
3.5 |
280 |
|
YLB200-150-315A |
1450 |
374 |
28 |
75 |
38 |
55 |
3.5 |
280 |
|
YLB200-150-400 |
1450 |
400 |
50 |
78 |
69.8 |
90 |
3.8 |
340 |
|
YLB200-150-400A |
1450 |
374 |
44 |
76 |
58.94 |
75 |
3.8 |
340 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: ylb filter press feed pump, China ylb filter press feed pump manufacturers, factory


