Product Overview
The rotor has a single-start thread. At any cross-section, its profile is a circle with a radius of R. The center of the cross-section lies on the helical centerline and is offset from the rotor axis by an eccentricity of e.
The inner surface of the stator has a double-start profile. Its cross-section is an elongated shape consisting of two semicircular ends with a radius of R, connected by a straight section with a length of 4e.
After the rotor is installed inside the stator, a series of sealed cavities is formed between the rotor surface and the internal helical surface of the stator. As the rotor rotates:
- The working cavity near the suction chamber gradually increases in volume, creating a negative pressure.
- Under the resulting pressure differential, the liquid is drawn into the working cavity.
- As rotation continues, the working cavity volume increases until it reaches its maximum.
- The cavity then becomes sealed and pushes the liquid axially toward the discharge chamber.
- The upper and lower working cavities alternately perform suction and discharge, enabling continuous liquid transfer.
- This operating principle provides smooth, continuous conveying with minimal disturbance to the medium.
Main Product Series
In China, single-screw pumps are currently divided mainly into the following two categories:
G-Series Single-Screw Pumps
The G-Series features a compact construction and offers the following performance range:
Capacity: 0.8–150 m³/h
Head: Up to 120 m
Operating pressure: ≤ 2.5 MPa
Operating temperature: Up to 120°C
Special high-temperature applications: Customized designs can convey media at temperatures up to 350°C
I-1B Series Thick-Slurry Pumps
The I-1B Series is designed for conveying thick slurries and offers the following performance range:
Capacity: 1.1–30 m³/h
Head: 50–120 m
The pump body is available in three configurations:
- Cast-iron casing
- Stainless-steel drive components
- All-stainless-steel construction
- Main Characteristics
Single-screw pumps have been widely used in developed countries. Due to their excellent performance, their applications in China are also expanding rapidly.
Their key advantages include:
- Broad adaptability to different process media
- Stable and uniform flow
- Low pressure pulsation
- Strong self-priming capability
- Gentle handling of the conveyed medium
- Continuous, smooth conveying performance
These characteristics make single-screw pumps particularly suitable for applications where other pump types are difficult to replace.
Product Features
Excellent Media Compatibility and Wide Application Range
Single-screw pumps can handle fluids with viscosities ranging from water-like liquids to nearly solid materials. The applicable viscosity can reach 200,000 cP or higher.
They can also convey media containing solid particles or fibers:
- Particle diameter: up to 30 mm, provided it does not exceed the rotor eccentricity
- Fiber length: up to 350 mm, equivalent to approximately 0.4 times the rotor pitch
- Typical solids content: up to approximately 40% by volume
- Fine powder solids content: up to 60% by volume or higher
Smooth, Pulsation-Free Conveying with No Shear Effect
Single-screw pumps typically operate at relatively low speeds, providing exceptionally smooth and gentle conveying with minimal shear.
The conveyed medium remains uniform and is not subjected to significant turbulence or vortex formation. Since the volume of the medium remains essentially unchanged during conveying, the pump produces little agitation or churning. This makes it particularly suitable for handling sensitive media and products that are susceptible to shear damage.
Capability for Multiphase Conveying
The helical sealing lines formed by contact between the rotor and stator completely separate the suction chamber from the discharge chamber.
This gives the pump a valve-like isolating function and enables the simultaneous conveying of liquids, gases, and solids in multiphase media.
Excellent Self-Priming Capability
Single-screw pumps offer excellent self-priming performance, with a suction lift of approximately 6–8.5 m of water column or more. A foot valve is not required for pump start-up.
Compared with centrifugal pumps, single-screw pumps generally require fewer auxiliary valves and provide more stable flow.
Flow Rate Proportional to Speed for Convenient Adjustment
The flow rate of a single-screw pump is linearly proportional to its rotational speed. The flow can therefore be conveniently controlled by adjusting the pump speed.
When equipped with a variable-frequency motor, the pump can function as a variable-flow pump and is commonly used for metering applications.
Stable Operation with Staged Pressure Capability
The discharge pressure of each pump stage is approximately 0.6 MPa. The rated discharge pressure can be increased by adding stages, allowing the pump to meet different system pressure requirements.
The pump provides:
- Stable operation
- Consistent discharge pressure
- Low noise
- Flexible pressure configuration through the addition of stages
Selectable Rotor and Stator Materials for Different Service Conditions
Rotor materials:
Depending on the characteristics of the conveyed medium, the rotor can be manufactured from materials such as:
- 40Cr alloy steel
- 304 stainless steel
- 316L stainless steel
- 2205 duplex stainless steel
Following surface hardening, rotor hardness can reach HRC 55, providing excellent wear resistance. With special polishing, the surface roughness can be reduced to approximately Ra 0.2 μm.
Stator materials:
A variety of rubber formulations are available to meet different operating requirements. Common stator materials include:
Nitrile rubber (NBR):Oil-resistant; up to 120°C
Ethylene propylene diene monomer rubber (EPDM) :Acid- and alkali-resistant; up to 150°C; food-grade options available
Fluoroelastomer (FKM) :Resistant to highly corrosive media; up to 200°C
Polyurethane rubber :Excellent wear resistance
Silicone rubber: Food-grade and pharmaceutical-grade options available
These material options enable the pump to handle abrasive, corrosive, high-temperature, and other demanding operating conditions.
Modular Design for Convenient Maintenance
The single-screw pump has a compact structure and a limited number of components. The rotor and stator are the primary wear parts, and their simple construction makes disassembly, installation, and replacement convenient.
The modular design allows the pump to be adapted to different operating conditions simply by replacing the rotor and stator, reducing maintenance time and simplifying spare-parts management.
Energy-Efficient Operation
The pump generates minimal internal sliding friction and turbulence during operation, resulting in low energy losses. It can also operate at relatively low speeds, which helps reduce wear and extend service life.
The drive system can be configured in several ways, including:
- Direct coupling
- Low-speed motor with V-belt drive
- Gearbox drive
- Variable-speed transmission
- Continuously variable transmission
Overall, the single-screw pump combines gentle conveying, stable flow, strong self-priming capability, flexible material selection, and efficient operation, making it suitable for a wide range of demanding process applications.
Applications
Due to their broad compatibility with different process media, single-screw pumps are widely used in the following industrial sectors:
Environmental Protection:
Conveying industrial wastewater, domestic sewage, sludge, and turbid water containing solid particles and short fibers. They are particularly suitable for integration with oil–water separators, recessed-chamber filter presses, and other treatment equipment.
01
Petroleum Industry:
Conveying crude oil, crude oil–water mixtures, coalbed methane–water mixtures, and polymers for injection into underground formations.
02
Chemical Industry:
Handling various suspensions, greases, colloidal slurries, adhesives, and corrosive media such as strong acids, strong alkalis, and organic solvents.
03
Food and Brewing Industries:
Conveying viscous starch, concentrated distiller's grains, grain-processing residues, sauces, pastes, slurries containing solids, honey, syrup, fruit purée, cream, and other viscous food products.
04
Pharmaceutical and Personal-Care Industries:
Conveying various viscous slurries, emulsions, ointments, cosmetics, pharmaceutical intermediates, and other high-viscosity products.
05
Paper Manufacturing:aper Industry:
Handling high-viscosity inks, PVC polymer pastes used in wallpaper production, paper pulp of various consistencies, and short-fiber pulp suspensions.
06
Construction Industry:
Conveying and spraying cement mortar, lime slurry, coatings, and other paste-like materials.
07
Mining Industry:
Conveying solid particles, mine water, and contaminated slurry water in underground mining operations.
08
Marine and Shipbuilding Industries:
Conveying media associated with bilge cleaning, including oily water, oil residues, and oily wastewater.
09
Power Plants and Industrial Boilers:
Conveying coal–water slurry.Single-screw pumps are particularly well suited to applications involving high-viscosity, abrasive, corrosive, solid-laden, or shear-sensitive media, where stable flow and gentle conveying are essential.
10
Technical Specifications
Design Standards:
The performance parameters of most models in the G (LB) Series Single-Screw Pump comply with JB/T 8644-1997, as verified and approved through the appraisal conducted by the former Ministry of Machinery Industry of China.
The products may be designed and manufactured with reference to GB/T 10885, Technical Conditions for Single-Screw Pumps, ISO 15136, and other applicable standards.
Working Principle:
A single-screw pump is an internally meshing, eccentric rotary positive-displacement pump. Its principal working components consist of a stator with a double-start helical cavity and a rotor that meshes with the stator.
As the rotor performs planetary motion around the stator axis inside the stator cavity, sealed cavities are formed between the rotor and stator. These cavities move axially along the rotor, conveying the liquid evenly, continuously, and at a constant rate from the suction port to the discharge port.
According to the number-of-starts ratio-the number of stator threads to the number of rotor threads-the pump can be classified as:
Single-start configuration: 1:2
Multi-start configurations: 2:3, 3:4, etc.
A higher number-of-starts ratio provides higher output torque and lower rotational speed. Conversely, a lower ratio results in lower torque and higher rotational speed.
Structural Components:
Rotor:
The rotor is an eccentric helical screw. Available materials include:
- 40Cr alloy steel
- 304 stainless steel
- 316L stainless steel
- 2205 duplex stainless steel
- Stator
The stator is a sleeve with an internal double-start helical surface. It is typically manufactured by vulcanizing an elastomer lining inside a metal tube.
Universal Joint / Drive Shaft
The universal joint or drive shaft is equipped with an external rubber protective sleeve and internally grease-lubricated components. It adopts a standardized cross-joint configuration, providing:
- High transmission torque
- High reliability
- Long service life
Shaft Seal
Several sealing arrangements are available, including:
- Packing seal
- Single mechanical seal
- Double mechanical seal
Drive System
The pump can be driven by various arrangements, including:
- Direct motor coupling
- V-belt drive
- Gearbox drive
- Continuously variable transmission
Working Conditions:
Rated operating pressure:Approximately 0.6 MPa per stage; higher pressures can be achieved through multistage series operation, with a maximum of approximately 2.4 Mpa
Medium temperature:Standard range: −20°C to +120°C with NBR or EPDM stators; special designs can handle temperatures up to 350°C
Medium viscosity:Up to 200,000 cP; certain applications can reach up to 1,000,000 cP
Solids content:Generally up to 40% by volume; fine powders can reach 60% by volume or higher
Maximum particle diameter:Up to 30 mm, provided that it does not exceed the rotor eccentricity
Maximum fiber length:Up to 350 mm, equivalent to approximately 0.4 times the rotor pitch
Self-priming capability:Suction lift of approximately 6–8.5 m
Reference Guide for Stator Elastomer Selection
Design Standards:
The performance parameters of most models in the G (LB) Series Single-Screw Pump comply with JB/T 8644-1997, as verified and approved through the appraisal conducted by the former Ministry of Machinery Industry of China.
The products may be designed and manufactured with reference to GB/T 10885, Technical Conditions for Single-Screw Pumps, ISO 15136, and other applicable standards.
Working Principle:
A single-screw pump is an internally meshing, eccentric rotary positive-displacement pump. Its principal working components consist of a stator with a double-start helical cavity and a rotor that meshes with the stator.
As the rotor performs planetary motion around the stator axis inside the stator cavity, sealed cavities are formed between the rotor and stator. These cavities move axially along the rotor, conveying the liquid evenly, continuously, and at a constant rate from the suction port to the discharge port.
According to the number-of-starts ratio-the number of stator threads to the number of rotor threads-the pump can be classified as:
Single-start configuration: 1:2
Multi-start configurations: 2:3, 3:4, etc.
A higher number-of-starts ratio provides higher output torque and lower rotational speed. Conversely, a lower ratio results in lower torque and higher rotational speed.
Structural Components:
Rotor:
The rotor is an eccentric helical screw. Available materials include:
- 40Cr alloy steel
- 304 stainless steel
- 316L stainless steel
- 2205 duplex stainless steel
- Stator
The stator is a sleeve with an internal double-start helical surface. It is typically manufactured by vulcanizing an elastomer lining inside a metal tube.
Universal Joint / Drive Shaft
The universal joint or drive shaft is equipped with an external rubber protective sleeve and internally grease-lubricated components. It adopts a standardized cross-joint configuration, providing:
- High transmission torque
- High reliability
- Long service life
Shaft Seal
Several sealing arrangements are available, including:
- Packing seal
- Single mechanical seal
- Double mechanical seal
Drive System
The pump can be driven by various arrangements, including:
- Direct motor coupling
- V-belt drive
- Gearbox drive
- Continuously variable transmission
Working Conditions:
Rated operating pressure:Approximately 0.6 MPa per stage; higher pressures can be achieved through multistage series operation, with a maximum of approximately 2.4 Mpa
Medium temperature:Standard range: −20°C to +120°C with NBR or EPDM stators; special designs can handle temperatures up to 350°C
Medium viscosity:Up to 200,000 cP; certain applications can reach up to 1,000,000 cP
Solids content:Generally up to 40% by volume; fine powders can reach 60% by volume or higher
Maximum particle diameter:Up to 30 mm, provided that it does not exceed the rotor eccentricity
Maximum fiber length:Up to 350 mm, equivalent to approximately 0.4 times the rotor pitch
Self-priming capability:Suction lift of approximately 6–8.5 m
Reference Guide for Stator Elastomer Selection
The stator is a key wear component of a single-screw pump. Its material selection has a direct effect on pump service life.
Under normal operating conditions, the typical service life of the stator lining is approximately 3–6 months. Improper material selection may cause the elastomer lining to detach from the steel tube or suffer chunking and local material loss.
The following table provides general guidance for selecting stator materials:
|
Elastomer Type |
Typical Applications |
Temperature Range |
Limitations |
|
Nitrile rubber (NBR) |
Petroleum-based media, lubricating oils, water |
≤120°C |
Not resistant to strong oxidizing agents or strong acids |
|
Hydrogenated nitrile rubber (HNBR) |
High-temperature oils, sour crude oil |
≤150°C |
Relatively high cost |
|
Fluoroelastomer (FKM) |
Strong acids, strong alkalis, solvents, ketones, esters |
≤200°C |
Lower elasticity and higher cost |
|
Ethylene propylene diene monomer rubber (EPDM) |
Hot water, detergents, weak acids and alkalis, food-grade applications |
≤150°C |
Not resistant to oil-based media |
|
Polyurethane rubber (AU/EU) |
Particle-laden slurries and highly abrasive applications |
≤80°C |
Limited high-temperature resistance |
The actual stator material should be selected based on the medium's chemical composition, temperature, viscosity, solids content, abrasiveness, and operating pressure.
Important Operating Precautions:
The pump must not be operated without an adequate supply of medium. Dry running is strictly prohibited. If dry running occurs, friction between the rotor and the rubber stator can generate excessive heat within a very short time, resulting in stator damage or burnout.
During installation, the motor shaft and pump shaft must be properly aligned. The allowable alignment deviation is ≤ ±0.2 mm. A filtration device should also be installed where required by the application.
After conveying high-viscosity media, the piping system should be thoroughly flushed to prevent blockage, solidification, or material deposition.
General Performance Range:
a. Capacity, Q: 0.8–150 m³/h; standard range for the G Series
b. Head, H: 0–120 m; higher heads can be achieved with multistage configurations
c. Operating pressure: Approximately 0.6 MPa per stage; ≤2.4 MPa for multistage configurations; higher pressures can be achieved through series operation
d. Speed, n: 230–1,400 r/min; adjustable according to operating conditions
e. Medium temperature: −20°C to +120°C under standard conditions; up to 350°C with special designs
f. Medium viscosity: ≤200,000 cP; up to 1,000,000 cP in certain applications
g. Solid content: ≤40% by volume; 60% by volume or higher for fine powders
h. Maximum particle diameter: ≤30 mm, and not greater than the rotor eccentricity
i. Maximum fiber length: ≤350 mm, approximately 0.4 times the rotor pitch
j. Self-priming capability: 6–8.5 m suction lift; no foot valve required
k. Motor power: 0.37–15 kW, selected according to operating conditions
Structural Drawings

Performance Data Tables
|
Pump Model |
Maximum Allowable Particle Size in Medium (mm) |
Standard Speed, n (r/min) |
Operating Pressure, p (bar) |
Capacity with Water, Q (m³/h) |
Shaft Power with Water, P (kW) |
|
015-01l06- |
2 |
160 |
0-6 |
0.15-0.1 |
0.1 |
|
200 |
0.19-0.14 |
0.1 |
|||
|
250 |
0.23-0.18 |
0.1 |
|||
|
315 |
0.29-0.25 |
0.12 |
|||
|
400 |
0.37-0.30 |
0.14 |
|||
|
500 |
0.47-0.38 |
0.16 |
|||
|
630 |
0.59-0.50 |
0.19 |
|||
|
795 |
0.74-0.64 |
0.26 |
|||
|
021-01L06- |
3 |
160 |
0-6 |
0.44-0.3 |
0.25 |
|
200 |
0.55-0.4 |
0.27 |
|||
|
250 |
0.69-0.6 |
0.29 |
|||
|
315 |
0.87-0.7 |
0.3 |
|||
|
400 |
1.10-1.0 |
0.35 |
|||
|
500 |
1.38-1.2 |
0.4 |
|||
|
630 |
1.74-1.5 |
0.5 |
|
031-01L06- |
4.5 |
160 |
0-6 |
1.32-0.9 |
0.4 |
|
200 |
1.66-1.2 |
0.45 |
|||
|
250 |
2.10-1.3 |
0.5 |
|||
|
315 |
2.64-2.0 |
0.6 |
|||
|
400 |
3.32-2.8 |
0.75 |
|||
|
500 |
4.18-3.6 |
0.85 |
|||
|
630 |
5.23-4.5 |
1.1 |
|||
|
038-01L06- |
7 |
125 |
0-6 |
2.94-1.5 |
0.7 |
|
160 |
3.70-2.5 |
0.9 |
|||
|
200 |
4.66-3.2 |
1.05 |
|||
|
250 |
5.86-4.5 |
1.25 |
|||
|
315 |
7.33-5.6 |
1.5 |
|||
|
400 |
9.29-7.7 |
1.9 |
|||
|
500 |
11.7-10 |
2.75 |
|||
|
045-01L06- |
8.5 |
125 |
0-6 |
5.17-3.0 |
1.5 |
|
160 |
6.50-7.0 |
1.5 |
|||
|
200 |
8.19-7.0 |
1.8 |
|||
|
250 |
10.03-9.0 |
2.2 |
|||
|
315 |
13.0-11.5 |
2.7 |
|||
|
400 |
16.3-15.5 |
3.3 |
|||
|
500 |
20.3-18 |
4.4 |
|||
|
053-01L06- |
10 |
100 |
0-6 |
7.32-4.5 |
1.7 |
|
125 |
9.22-6.0 |
1.9 |
|||
|
160 |
11.6-8.0 |
2.2 |
|||
|
200 |
14.6-11 |
2.8 |
|||
|
250 |
18.4-14 |
3.4 |
|||
|
315 |
23.2-18.0 |
4.5 |
|||
|
400 |
29.1-24 |
5.5 |
|||
|
063-01L06- |
12.5 |
100 |
0-6 |
12.4-5.0 |
2.4 |
|
125 |
15.6-10 |
2.7 |
|||
|
160 |
19.6-12 |
3.3 |
|||
|
200 |
21.6-18.5 |
4.3 |
|||
|
250 |
31.0-23 |
5.5 |
|||
|
315 |
39.1-31 |
7 |
|||
|
400 |
49.2-40.2 |
8.9 |
|||
|
076-01L06- |
15 |
80 |
0-6 |
16.4-12 |
3.5 |
|
100 |
20.7-14 |
4 |
|||
|
125 |
26.1-17 |
5 |
|||
|
160 |
32.8-25 |
6 |
|||
|
200 |
41.3-33 |
8 |
|||
|
250 |
52.0-42 |
10 |
|||
|
315 |
65.4-54 |
13 |
|
031-01L06- |
4.5 |
160 |
0-6 |
1.32-0.9 |
0.4 |
|
200 |
1.66-1.2 |
0.45 |
|||
|
250 |
2.10-1.3 |
0.5 |
|||
|
315 |
2.64-2.0 |
0.6 |
|||
|
400 |
3.32-2.8 |
0.75 |
|||
|
500 |
4.18-3.6 |
0.85 |
|||
|
630 |
5.23-4.5 |
1.1 |
|||
|
038-01L06- |
7 |
125 |
0-6 |
2.94-1.5 |
0.7 |
|
160 |
3.70-2.5 |
0.9 |
|||
|
200 |
4.66-3.2 |
1.05 |
|||
|
250 |
5.86-4.5 |
1.25 |
|||
|
315 |
7.33-5.6 |
1.5 |
|||
|
400 |
9.29-7.7 |
1.9 |
|||
|
500 |
11.7-10 |
2.75 |
|||
|
045-01L06- |
8.5 |
125 |
0-6 |
5.17-3.0 |
1.5 |
|
160 |
6.50-7.0 |
1.5 |
|||
|
200 |
8.19-7.0 |
1.8 |
|||
|
250 |
10.03-9.0 |
2.2 |
|||
|
315 |
13.0-11.5 |
2.7 |
|||
|
400 |
16.3-15.5 |
3.3 |
|||
|
500 |
20.3-18 |
4.4 |
|||
|
053-01L06- |
10 |
100 |
0-6 |
7.32-4.5 |
1.7 |
|
125 |
9.22-6.0 |
1.9 |
|||
|
160 |
11.6-8.0 |
2.2 |
|||
|
200 |
14.6-11 |
2.8 |
|||
|
250 |
18.4-14 |
3.4 |
|||
|
315 |
23.2-18.0 |
4.5 |
|||
|
400 |
29.1-24 |
5.5 |
|||
|
063-01L06- |
12.5 |
100 |
0-6 |
12.4-5.0 |
2.4 |
|
125 |
15.6-10 |
2.7 |
|||
|
160 |
19.6-12 |
3.3 |
|||
|
200 |
21.6-18.5 |
4.3 |
|||
|
250 |
31.0-23 |
5.5 |
|||
|
315 |
39.1-31 |
7 |
|||
|
400 |
49.2-40.2 |
8.9 |
|||
|
076-01L06- |
15 |
80 |
0-6 |
16.4-12 |
3.5 |
|
100 |
20.7-14 |
4 |
|||
|
125 |
26.1-17 |
5 |
|||
|
160 |
32.8-25 |
6 |
|||
|
200 |
41.3-33 |
8 |
|||
|
250 |
52.0-42 |
10 |
|||
|
315 |
65.4-54 |
13 |
Notes
1.The speed series ratio is 1.122.
2.This table is based on standard operating conditions, with water at 20°C as the pumped medium. The listed values represent the corresponding capacity and shaft power.
3.When selecting the gearbox, the speed may be determined within a range of −3% to +5% relative to the specified value.
4.The speeds listed above are the recommended operating speeds for each pump at its rated pressure. If the required speed falls outside this range, please consult our company for confirmation.

If you did not find the required parameters or models in our products, please feel free to contact us. Our company's technical staff will provide you with quick selection and customized technical solutions.
Hot Tags: single screw pump, China single screw pump manufacturers, factory


