Product Overview
The ZW Self-Priming Non-Clogging Sewage Pump is a new-generation solids-handling pump that combines self-priming capability with non-clogging sewage-pumping performance.
Developed through extensive research into comparable products and technologies in China and overseas, the pump adopts an axial liquid-return, external-mixing self-priming system.
Through the unique matching of the pump casing and impeller flow passages, the pump can be started without installing a foot valve or filling the suction line with priming water, while also conveying liquids containing large solid particles and long fibrous materials.
Product Classification
According to the material of construction, the pump is available in:
Cast iron
- Stainless steel, including 304, 316, and 316L
- According to the drive and structural configuration, the pump is available in two types:
- Split-coupled type, equipped with a bearing housing and coupling; designation: ZW
- Close-coupled type, with the pump shaft directly connected to the motor shaft; designation: ZWL
Model Designation
Example: 100ZW80-20
|
100 |
Pump suction and discharge diameter: 100 mm |
|
ZW |
Self-priming non-clogging sewage pump |
|
80 |
Flow rate at the design point: 80 m³/h |
|
20 |
Head at the design point: 20 m |
Product Features
1. Non-Clogging Impeller Design and Powerful Sewage-Handling Capability
The pump adopts a unique dual-vane impeller design with wide and unobstructed flow passages.
It can convey sewage and waste liquids containing large solid particles and long fibrous materials, effectively addressing the clogging problems commonly associated with conventional sewage pumps.
Suspended solids with a diameter of up to 60% of the pump port diameter can pass through the pump.
Fibrous materials with a length of up to five times the pump port diameter can also be conveyed.
2. High-Performance Self-Priming: "Prime Once, Self-Prime Throughout Service Life"
A liquid storage chamber is incorporated into the pump casing. Together with the liquid-return passage and circulation passage, it forms an axial liquid-return, external-mixing self-priming system.
After the initial filling, the pump does not require additional priming before subsequent start-ups. The self-priming height can reach 5–6 m, with a short self-priming time of approximately 3 minutes at a 5 m suction lift.
No foot valve is required in the suction line.
3. High Efficiency and Energy Savings
The pump features an advanced hydraulic design. Its efficiency is approximately 3%–5% higher than that of conventional self-priming pumps.
This provides significant energy savings and helps prevent the motor from operating under overload conditions within the specified design range.
4. Compact Construction and Convenient Installation and Maintenance
The pump has a compact overall structure, small footprint, and low operating noise.
Maintenance and inspection are convenient. The coupling drive provides stable operating performance, and routine maintenance can be completed without personnel entering the sewage pit.
When equipped with an outdoor-duty motor with an IP54/IP55 protection rating, the pump can be installed outdoors without the need for a dedicated pump room, helping reduce infrastructure costs.
5. Wear-Resistant and Reliable Mechanical Seal
The pump uses a new-generation mechanical seal with a wear-resistant alloy friction pair.
The seal operates inside an oil chamber, providing effective lubrication and favorable operating conditions. This design offers long service life and high operational reliability.
6. Comprehensive Automatic Control Functions
An automatic control cabinet can be supplied according to customer requirements.
The control system can automatically start and stop the pump according to changes in liquid level, eliminating the need for continuous on-site supervision.
This makes the pump convenient to operate and facilitates automated system management.
7. Wide Range of Available Materials for Different Media
The pump casing is available in several materials, including:
Cast iron
Ductile iron
Cast steel
Stainless steel, including 304, 316, and 316L
Cast iron pumps are suitable for media with a pH value of 6–9.
Stainless steel pumps are suitable for media with a pH value of 1–14.
This broad material selection enables the pump to handle media with different levels of corrosiveness.
8. A Full Alternative to Submersible Sewage Pumps
The ZW Self-Priming Non-Clogging Sewage Pump can be installed above the liquid level while drawing and discharging sewage from a low-level sump.
It can serve as a full alternative to submersible sewage pumps such as the WQ and QW series, avoiding common problems associated with submersible motors operating in sewage, including:
- Motor damage caused by prolonged immersion
- Difficult inspection and maintenance
- Complicated removal and servicing procedures
Applications
The ZW Self-Priming Non-Clogging Sewage Pump is widely used for conveying sewage, wastewater, and waste liquids containing solid particles and long fibrous materials, as well as mildly corrosive media.
Typical applications include:
- Municipal sewage systems: Drainage systems at municipal wastewater treatment plants, municipal sewage pumping stations, stormwater pumping stations, sewer flushing and desilting, and river pollution interception
- Industrial wastewater treatment: Industrial wastewater and workshop drainage in the chemical, pharmaceutical, textile dyeing, paper, electroplating, and surface-treatment industries
- Construction sites and foundation-pit dewatering: Deep foundation-pit dewatering, basement drainage, and drainage for civil defense projects
- Mining and tunnel construction: Mine drainage, tunnel-construction drainage, and conveying settled mining wastewater and impurities in non-hazardous areas
- Agricultural irrigation and aquaculture: Farmland floodwater drainage, wastewater discharge and water replacement in fish and shrimp ponds, and manure handling
- Food-processing plants and slaughterhouses: Discharging wastewater containing complex materials such as bone fragments, blood clots, grease, and offal residues
- Paper, textile, and light industries: Pulp discharge, fiber-slurry conveying, and wastewater containing fibrous materials
- Power industry: Drainage from ash slurry ponds at power plants and supporting systems for flue-gas desulfurization
- Hospitals and hotels: Sewage discharge stations and wastewater systems for public facilities
- Waterworks: Water-supply equipment and raw-water conveyance
- River and pond aquaculture: River and pond desilting and manure handling
Technical Specifications
1. Design Standards
The ZW Self-Priming Non-Clogging Sewage Pump is designed in accordance with ISO 2858 and GB/T 5656.
The product complies with the following standards:
JB/T 6664-2017 - Self-Priming Pumps
JB/T 6535-92 - Technical Conditions for Centrifugal Sewage Pumps
Certain products are designed and manufactured in accordance with applicable company standards.
2. Construction and Configuration
Main Components
The ZW Self-Priming Sewage Pump mainly consists of the following components:
- Pump casing
- Impeller
- Rear cover
- Mechanical seal
- Pump shaft
- Bearing housing
- Inlet valve
- Gas-liquid separation pipe
- Water-filling valve
- Suction and discharge connecting pipes
The pump is available in two structural configurations:
Split-coupled type - ZW
The pump is equipped with a bearing housing. The pump shaft is driven by the motor shaft through a coupling.
Close-coupled type - ZWL
The pump shaft is directly connected to the motor shaft.
3. Operating Principle
A liquid storage chamber is incorporated into the pump casing. The chamber communicates with the pump working chamber through a liquid-return passage at the top and a circulation passage at the bottom, forming an axial liquid-return, external-mixing self-priming system.
After the pump stops, a certain volume of liquid remains in the liquid storage chamber.
When the pump starts, the rotating impeller throws the stored liquid upward together with the air. The gas-liquid mixture passes through the gas-liquid separation pipe and is separated:
The liquid returns to the working chamber through the grid-type return passage.
The gas is discharged from the pump.
As this process continues, a vacuum is gradually formed inside the pump, thereby achieving self-priming.
The impeller is housed in a separate impeller chamber. The strong axial vortex generated by the impeller creates a vacuum at the suction inlet and generates pressure at the discharge outlet, allowing impurities and solids to pass smoothly through the discharge chamber.
4. Shaft Sealing System
The pump uses a new-generation mechanical seal with wear-resistant alloy friction pairs.
The mechanical seal operates inside an oil chamber for long periods, providing effective lubrication and cooling conditions.
The seal adopts a double-ended, wear-resistant design, offering reliable sealing performance and extended service life.
5. Direction of Rotation
When viewed from the drive end, or motor end, the pump rotates counterclockwise.
6. Material Selection for Wetted Components
The materials for wetted components can be selected according to the properties of the pumped medium and the operating conditions.
|
Material |
Typical Application |
|
HT200 cast iron |
Neutral sewage and general industrial wastewater; medium pH 6–9 |
|
Ductile iron |
Sewage containing small amounts of abrasive particles; better wear resistance than ordinary cast iron |
|
Cast steel |
General industrial media and relatively high-temperature media |
|
304 stainless steel |
General corrosive wastewater; medium pH 1–14 |
|
316/316L stainless steel |
Highly corrosive wastewater containing chloride ions and similar components; excellent resistance to pitting corrosion |
7. Operating Conditions
The standard operating conditions are as follows:
|
Parameter |
Specification |
|
Flow rate, Q |
5–800 m³/h, covering the complete range of standard and cutter-impeller models |
|
Head, H |
12–80 m; may exceed 80 m under certain configurations |
|
Speed, n |
1,450 / 2,900 rpm; 2,900 rpm is generally used for low-flow, high-head applications |
|
Suction lift / self-priming height |
4.5–6.0 m; up to 6 m under clean-water conditions |
|
Self-priming time |
Approximately 3–5 minutes at a 5 m suction lift under clean-water conditions |
|
Medium temperature |
≤60°C under standard conditions; up to 200°C for special configurations, depending on the materials of the wetted components |
|
Ambient temperature |
≤50°C |
|
Medium density |
≤1,240 kg/m³ |
|
Total impurity content by weight |
≤15% of the total medium weight |
|
Passable particle diameter |
≤60% of the pump port diameter for suspended particles |
|
Passable fiber length |
≤5 times the pump port diameter |
|
Medium pH value |
Cast iron: 6–9; stainless steel: 1–14; subject to material selection |
|
Port diameter range |
Ø25–Ø300 mm for suction and discharge ports |
|
Motor power |
2.2–55 kW, calculated according to medium density and operating conditions |
|
Efficiency, η |
45%–65% |
|
Required NPSH |
2.0–6.0 m |
|
Design pressure |
≤2.0 MPa |
8. Important Operating Precautions
a. Initial Filling
Before the first start-up, fill the pump casing with a sufficient quantity of liquid. The filling volume must be no less than two-thirds of the pump casing volume.
Dry running is strictly prohibited.
No additional filling is required for subsequent start-ups under normal conditions.
b. Checking the Direction of Rotation
Check the direction of rotation before operation.
When viewed from the motor end, the pump should rotate clockwise. Reverse operation is strictly prohibited.
c. Suction-Line Sealing
The suction line must be completely airtight.
Any air leakage will seriously affect the self-priming performance of the pump.
d. Maximum Suction Height and Suction-Line Length
The self-priming height must not exceed the specified range of 4.5–6.0 m.
The suction-line length should not exceed 10 m.
e. Failure to Discharge Liquid
If the pump fails to discharge liquid within the specified self-priming height after continuous operation for more than 5–10 minutes, stop the pump immediately and investigate the cause.
This is necessary to prevent the working liquid inside the pump from overheating and causing damage.
f. Cold-Weather Protection
If the pump will remain unused for an extended period during winter, drain all liquid from the pump casing to prevent damage caused by freezing.
g. Information Required for Special Media
When conveying special media, provide the following information so that the manufacturer can select suitable materials and configure the pump correctly:
- Medium name
- Temperature
- Concentration
- Density
- Viscosity
- Solid-particle concentration
- Particle size
- Other relevant operating conditions
Structural Drawings

Performance Data Tables
|
Model |
Flow Rate, Q (m³/h) |
Head, H (m) |
Motor Power (kW) |
Speed (rpm) |
Efficiency, η (%) |
Required NPSH (m) |
Self-Priming Height (m) |
Self-Priming Time (min/5 m) |
Weight (kg) |
|
25ZW8-15 |
8 |
15 |
1.5 |
2900 |
45 |
2 |
5.5 |
3 |
100 |
|
32ZW5-20 |
5 |
20 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
32ZW10-20 |
10 |
20 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
32ZW9-30 |
9 |
30 |
3 |
2900 |
48 |
2.5 |
5.5 |
3 |
120 |
|
32ZW20-12 |
20 |
12 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
40ZW10-20 |
10 |
20 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
40ZW20-12 |
20 |
12 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
40ZW20-15 |
20 |
15 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
40ZW15-30 |
15 |
30 |
3 |
2900 |
48 |
2.5 |
5.5 |
3 |
120 |
|
50ZW10-20 |
10 |
20 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
50ZW20-12 |
20 |
12 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
100 |
|
50ZW15-30 |
15 |
30 |
3 |
2900 |
48 |
2.5 |
5.5 |
3 |
120 |
|
50ZW20-35 |
20 |
35 |
5.5 |
2900 |
48 |
2.5 |
5.5 |
3 |
150 |
|
65ZW30-18 |
30 |
18 |
4 |
1450 |
45 |
2.5 |
5.5 |
3 |
200 |
|
65ZW20-30 |
20 |
30 |
5.5 |
2900 |
50 |
3 |
5.5 |
3 |
200 |
|
65ZW25-30 |
25 |
30 |
5.5 |
2900 |
50 |
3 |
5.5 |
3 |
200 |
|
65ZW15-30 |
15 |
30 |
3 |
2900 |
48 |
2.5 |
5.5 |
3 |
120 |
|
65ZW20-14 |
20 |
14 |
2.2 |
2900 |
45 |
2.5 |
5.5 |
3 |
120 |
|
65ZW25-40 |
25 |
40 |
7.5 |
2900 |
50 |
3 |
5.5 |
2 |
200 |
|
65ZW40-25 |
40 |
25 |
7.5 |
1450 |
50 |
3 |
5.5 |
2 |
200 |
|
65ZW65-25 |
65 |
25 |
11 |
2900 |
52 |
3 |
5.5 |
2 |
240 |
|
80ZW40-16 |
40 |
16 |
4 |
1450 |
50 |
3 |
5 |
3 |
240 |
|
80ZW40-25 |
40 |
25 |
7.5 |
1450 |
50 |
3 |
5.5 |
2 |
200 |
|
80ZW25-40 |
25 |
40 |
7.5 |
2900 |
50 |
3 |
5.5 |
2 |
200 |
|
80ZW65-25 |
65 |
25 |
11 |
2900 |
52 |
3 |
5.5 |
2 |
240 |
|
80ZW80-35 |
80 |
35 |
15 |
2900 |
45 |
3 |
5.5 |
3 |
285 |
|
80ZW50-60 |
50 |
60 |
22 |
2900 |
55 |
3 |
5 |
3 |
340 |
|
100ZW100-15 |
100 |
15 |
7.5 |
1450 |
50 |
4 |
5.5 |
3 |
300 |
|
100ZW80-20 |
80 |
20 |
7.5 |
1450 |
53 |
4 |
5.5 |
3 |
300 |
|
100ZW100-20 |
100 |
20 |
11 |
1450 |
53 |
4 |
5.5 |
3 |
340 |
|
100ZW100-30 |
100 |
30 |
22 |
2900 |
53 |
4 |
5.5 |
2 |
510 |
|
100ZW80-60 |
80 |
60 |
37 |
2900 |
53 |
4 |
5 |
3 |
510 |
|
100ZW80-80 |
80 |
80 |
45 |
2900 |
50 |
4 |
5 |
3 |
510 |
|
125ZW120-20 |
120 |
20 |
15 |
1450 |
55 |
4.5 |
5.5 |
2 |
500 |
|
125ZW200-15 |
200 |
15 |
15 |
1450 |
55 |
4.5 |
5.5 |
2 |
500 |
|
150ZW180-14 |
180 |
14 |
15 |
1450 |
60 |
5 |
5.5 |
3.5 |
500 |
|
150ZW200-15 |
200 |
15 |
15 |
1450 |
60 |
5 |
5.5 |
3 |
570 |
|
150ZW180-20 |
180 |
20 |
22 |
1450 |
60 |
5 |
5 |
3 |
570 |
|
150ZW250-25 |
250 |
25 |
45 |
2900 |
60 |
5 |
5 |
2 |
680 |
|
150ZW180-30 |
180 |
30 |
37 |
1450 |
65 |
5 |
5 |
3 |
680 |
|
150ZW180-38 |
180 |
38 |
55 |
1450 |
45 |
5 |
6 |
3.5 |
800 |
|
200ZW280-14 |
280 |
14 |
22 |
1450 |
65 |
5 |
5 |
3 |
700 |
|
200ZW300-18 |
300 |
18 |
37 |
1450 |
65 |
5 |
5 |
3 |
940 |
|
200ZW280-28 |
280 |
28 |
55 |
1450 |
55 |
4 |
5.2 |
3 |
940 |
|
250ZW420-20 |
420 |
20 |
55 |
1450 |
61 |
6 |
4.5 |
2.5 |
1150 |
|
300ZW800-14 |
800 |
14 |
55 |
1450 |
65 |
6 |
4.5 |
2.5 |
1400 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: zw self-priming non-clogging sewage pump, China zw self-priming non-clogging sewage pump manufacturers, factory


