Product Overview
The vertical inline pump is a single-stage, single-suction vertical centrifugal pump with an in-line configuration. Its inlet and outlet are located on the same centerline, allowing the pump to be installed directly in a pipeline as an extended pipe section. The motor is connected to the pump by a flexible coupling or drives it through an extended shaft. The compact design requires little floor space.
Typical applications include HVAC water circulation, heating systems, industrial cooling-water circulation, municipal water supply, fire-system pressurization and general industrial liquid transfer.
Designed with reference to GB/T 5656 and ISO 2858, the series is described as offering a wide flow range, moderate head, stable operation, low noise and convenient maintenance. The casing is available in cast iron or stainless steel. A closed or semi-open impeller can be selected, along with standard, hot-water, corrosion-resistant or explosion-protected configurations, for water, hot water, light oils and mildly corrosive liquids.
The stated operating-temperature ranges are −20°C to 120°C for the standard version and 120°C to 180°C for the hot-water version with water-cooled bearings. The stated maximum working pressure is 1.0–1.6 MPa.
Product Features
Inline vertical design
The inlet and outlet have the same nominal diameter and lie on the same centerline, allowing direct installation in a pipeline.
The compact footprint can reduce pump-room space requirements.
The motor is mounted above the pump, supporting heat dissipation and access for maintenance.
A floor-mounted support frame is available to improve installation stability.
Hydraulic performance
The pump uses an optimized hydraulic design and a closed impeller for efficient operation and reduced energy consumption.
The performance curve is described as relatively flat, with a broad high-efficiency operating range that accommodates flow variation.
The stated NPSHr is approximately 2.0–4.0 m, depending on the model and duty point.
Compact construction and convenient maintenance
With an extended coupling or extended-shaft motor arrangement, the impeller and mechanical seal can be removed for maintenance without removing the motor.
Deep-groove ball bearings are grease-lubricated and are intended to offer long maintenance intervals.
An air-vent plug and drain port are provided to facilitate venting and draining during maintenance.
Reliable shaft sealing
A mechanical seal is supplied as standard, with silicon-carbide/graphite seal faces for wear resistance and low leakage.
A cooling chamber can be selected for higher-temperature service to extend seal life.
A cartridge mechanical seal is available for easier installation and replacement.
Configurations for different duties
- Motor options: Standard, explosion-protected (Ex d II BT4) or variable-frequency-drive compatible.
- Materials: Cast iron, 304 stainless steel or 316L stainless steel.
- Temperature configurations: Standard service (−20°C to 80°C), hot-water service (80°C to 120°C), and high-temperature service (120°C to 180°C) with water cooling.
- Protection and insulation: IP54/IP55 protection; Class F insulation.
Low noise and vibration
The rotor is dynamically balanced to G6.3.
Direct motor-to-pump coupling is intended to support accurate alignment and stable operation.
The pump is suitable for locations where noise matters, such as HVAC and domestic water-supply pump rooms.
Applications
Buildings and municipal use
HVAC chilled-water and cooling-water circulation
Hot-water circulation in heating systems, including primary and secondary boiler circuits
Domestic water pressurization and fire-system pressure maintenance
Secondary water supply in high-rise buildings
Industrial applications
Cooling-water circulation for air compressors, injection-molding machines and heat exchangers
Process-water circulation
Factory water supply and pressurization
Condensate recovery and transfer
Municipal and environmental applications
Water-supply booster service
Intermediate transfer in wastewater-treatment plants
Irrigation and landscape watering
Other applications
- Boiler hot-water feed: Use the hot-water configuration.
- Mildly corrosive liquids: Select stainless-steel wetted parts.
- Light oils and solvents: Select an explosion-protected motor and seals suitable for the medium.
Technical Specifications
Design and Construction
|
Item |
Specification |
|
Pump type |
Vertical, single-stage, single-suction inline centrifugal pump |
|
Installation |
Direct pipeline installation as standard; floor-mounted support frame optional |
|
Connections |
Flanged; HG/T 20592 (PN16) standard, ANSI or DIN optional |
|
Impeller |
Closed for clean water; semi-open option for media with small quantities of solids |
|
Seal |
Mechanical seal; single or cartridge type available |
|
Bearings |
Deep-groove ball bearings; two upper bearings and one lower bearing, grease-lubricated |
|
Casing materials |
HT250 cast iron standard; QT450 or 304/316L stainless steel optional |
|
Rotation |
Clockwise when viewed from above the motor |
Operating Range
|
Parameter |
Stated range |
|
Flow rate, Q |
1.5–1,200 m³/h |
|
Head, H |
5–125 m |
|
Operating temperature |
−20°C to 120°C standard; up to 180°C for the water-cooled high-temperature version |
|
Maximum working pressure |
1.0 MPa (PN10) or 1.6 MPa (PN16) |
|
Speed |
1,450 / 2,900 r/min, depending on motor configuration |
|
Medium pH |
6–9 for cast iron; 3–12 for stainless steel |
|
Allowable solids content |
≤0.2%; particle diameter ≤0.2 mm |
|
NPSHr |
2.0–4.5 m, depending on flow and speed |
Material Options
|
Component |
Standard configuration (clean water) |
Optional configuration (hot water / mildly corrosive service) |
Optional configuration (corrosive / sanitary service) |
|
Casing |
HT250 cast iron |
HT250, hot-water version |
304 / 316L stainless steel |
|
Impeller |
HT250 cast iron |
HT250 / cast copper alloy |
304 / 316L stainless steel |
|
Shaft |
45# carbon steel |
2Cr13 stainless steel |
304 / 316L stainless steel |
|
Mechanical seal |
Graphite / silicon carbide |
Silicon carbide / silicon carbide for hot water |
Silicon carbide / tungsten carbide for corrosion-resistant service |
|
O-rings / seals |
NBR |
FKM |
PTFE |
|
Bearings |
Domestic precision bearings, e.g. 6204 / 6205 |
SKF / FAG / NSK optional |
Same as adjacent option |
Mechanical-Seal Selection Guide
|
Medium temperature or condition |
Recommended seal materials |
Special configuration |
|
−20°C to 80°C |
Graphite stationary face / silicon-carbide rotating face |
Standard single mechanical seal |
|
80°C to 120°C |
Silicon carbide / silicon carbide |
Cooling chamber required |
|
120°C to 180°C |
Silicon carbide / silicon carbide with high-temperature seal rings |
External cooling water required; hot-water version |
|
Small quantities of particles |
Silicon carbide / tungsten carbide |
Hard-on-hard seal faces |
|
Corrosive media |
Silicon carbide / silicon carbide with PTFE seal rings |
Stainless-steel pump with corrosion-resistant seal materials |
Referenced Standards
|
Category |
Standard |
Description |
|
Design and manufacture |
GB/T 5656-2008 |
Technical specifications for centrifugal pumps, Class II |
|
Inline pumps |
JB/T 6537-2006 |
Technical conditions for inline centrifugal pumps |
|
Dimensions |
GB/T 5662-2013 |
Marking, performance and dimensions for end-suction centrifugal pumps |
|
Performance testing |
GB/T 3216 |
Acceptance tests for hydraulic performance of rotodynamic pumps |
|
Explosion protection |
GB 3836 |
Optional Ex d II BT4 / CT4 |
|
Enclosure protection |
GB/T 4942.1 |
IP54 / IP55 |
Motor Options
|
Motor type |
Typical application |
Notes |
|
Y-type three-phase induction motor |
General clean-water and HVAC circulation |
Standard configuration |
|
YB explosion-protected motor |
Petroleum, chemical and potentially explosive areas |
Stated protection rating: Ex d II BT4 |
|
YVP variable-frequency motor |
Applications requiring flow or pressure adjustment |
Stated frequency range: 5–50 Hz |
|
Hot-water motor |
High-temperature circulation |
Separate fan and cooling fins |
Structural Drawings

Performance Data Tables
|
Model |
Flow rate (m³/h) |
Head (m) |
Speed (r/min) |
Motor power (kW) |
Efficiency (%) |
NPSHr (m) |
Voltage (V) |
|
15-80 |
1.5 |
8 |
2800 |
0.18 |
34 |
2.3 |
380 |
|
20-110 |
2.5 |
15 |
2800 |
0.37 |
34 |
2.3 |
380 |
|
20-160 |
2.5 |
32 |
2900 |
0.75 |
25 |
2.3 |
380 |
|
25-110 |
4 |
15 |
2900 |
0.55 |
42 |
2.3 |
380 |
|
25-125 |
4 |
20 |
2900 |
0.75 |
36 |
2.3 |
380 |
|
25-125A |
3.6 |
16 |
2900 |
0.55 |
35 |
2.3 |
380 |
|
25-160 |
4 |
32 |
2900 |
1.5 |
32 |
2.3 |
380 |
|
25-160A |
3.7 |
28 |
2900 |
1.1 |
31 |
2.3 |
380 |
|
32-100 |
4.5 |
12.5 |
2900 |
- |
44 |
- |
380 |
|
32-125 |
5 |
20 |
2900 |
1.1 |
- |
- |
380 |
|
32-125A |
4.5 |
16 |
2900 |
0.75 |
- |
- |
380 |
|
32-125(I) |
6.3 |
20 |
2900 |
1.1 |
- |
- |
380 |
|
32-160 |
6.5 |
32 |
2900 |
1.5 |
- |
- |
380 |
|
32-160I |
6.3 |
32 |
2900 |
2.2 |
- |
- |
380 |
|
32-160IA |
5 |
28 |
2900 |
1.5 |
- |
- |
380 |
|
32-160A |
4 |
25 |
2900 |
1.1 |
- |
- |
380 |
|
32-200I |
6.3 |
50 |
2900 |
4 |
- |
- |
380 |
|
32-200IA |
4.5 |
50 |
2900 |
3 |
- |
- |
380 |
|
32-200IB |
4 |
44 |
2900 |
2.2 |
- |
- |
380 |
|
40-100 |
6.3 |
12.5 |
2900 |
0.75 |
- |
- |
380 |
|
40-125 |
6.3 |
20 |
2900 |
1.1 |
- |
- |
380 |
|
40-160 |
6.3 |
32 |
2900 |
1.5 |
- |
- |
380 |
|
40-160A |
5 |
28 |
2900 |
1.5 |
- |
- |
380 |
|
40-200B |
5.5 |
38 |
2900 |
2.2 |
- |
- |
380 |
|
40-160(I) |
12.5 |
32 |
2900 |
3 |
- |
- |
380 |
|
40-200(I) |
12.5 |
50 |
2900 |
5.5 |
- |
- |
380 |
|
50-100A |
11 |
10 |
2900 |
0.75 |
- |
- |
380 |
|
50-200B |
10.5 |
35 |
2900 |
3 |
- |
- |
380 |
|
50-125(I)A |
22.4 |
16 |
2900 |
2.2 |
- |
- |
380 |
|
50-250(I)A |
23.4 |
70 |
2900 |
11 |
- |
- |
380 |
|
65-125 |
25 |
20 |
2900 |
3 |
- |
- |
380 |
|
65-250 |
25 |
80 |
2900 |
15 |
- |
- |
380 |
|
65-200 |
25 |
50 |
2900 |
7.5 |
- |
- |
380 |
|
65-100(I)A |
44.8 |
10 |
2900 |
2.2 |
- |
- |
380 |
|
65-200(I)B |
43 |
37 |
2900 |
7.5 |
- |
- |
380 |
|
80-100 |
50 |
12.5 |
2900 |
3 |
- |
- |
380 |
|
80-200A |
46.8 |
44 |
2900 |
11 |
- |
- |
380 |
|
80-315C |
41 |
85 |
2900 |
22 |
- |
- |
380 |
|
80-160(I) |
100 |
32 |
2900 |
15 |
- |
- |
380 |
|
80-250(I)B |
86.4 |
60 |
2900 |
30 |
- |
- |
380 |
|
100-125A |
89 |
16 |
2900 |
7.5 |
- |
- |
380 |
|
100-250A |
93.5 |
70 |
2900 |
30 |
- |
- |
380 |
|
100-350B |
80 |
135 |
2900 |
55 |
- |
- |
380 |
|
100-200(I)B |
138 |
40 |
2900 |
22 |
- |
- |
380 |
|
100-125(I)A |
168 |
12 |
2900 |
11 |
- |
- |
380 |
|
100-200(I)A |
168 |
40 |
2900 |
30 |
- |
- |
380 |
|
100-250(I)B |
100 |
65 |
2900 |
37 |
- |
- |
380 |
|
100-315 |
100 |
125 |
2950 |
75 |
66 |
4 |
380 |
|
100-350B |
82 |
135 |
2900 |
55 |
- |
- |
380 |
|
125-200B |
138 |
37 |
2900 |
22 |
- |
- |
380 |
|
125-100A |
143 |
10 |
2900 |
7.5 |
- |
- |
380 |
|
125-350 |
160 |
150 |
2900 |
110 |
- |
- |
380 |
|
150-200 |
160 |
50 |
2900 |
37 |
- |
- |
380 |
|
150-315B |
172 |
93 |
2900 |
75 |
- |
- |
380 |
|
150-315(I)A |
187 |
110 |
2900 |
90 |
- |
- |
380 |
|
200-500(I)B |
350 |
60 |
1450 |
- |
- |
- |
380 |
|
300-235 |
720 |
18 |
1480 |
55 |
81 |
81 |
380 |
|
300-380 |
480 |
48 |
970 |
132 |
- |
84 |
380 |
|
300-380A |
833 |
30 |
970 |
110 |
- |
- |
380 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Hot Tags: vertical inline pump, China vertical inline pump manufacturers, factory


